A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d 26 mm, andt= 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? ЗР Strain gage C |D H Answer: P = N

A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d 26 mm, andt= 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? ЗР Strain gage C |D H Answer: P = N

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b %3D = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a %3D compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P В D E Strain gage- d H b Answer: P = i N
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 10 mm while those at CD decrease 60 x 10 mm in the 250-mm-gage length. Using E= 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa, Given: a = 60 mm, b = 120 mm, and c = 80 mm. gage length a mm b mm Library entation c mm Survey DENTS TION
A test is conducted on a beam loaded by end couples. The fibres at layer CD are found to lengthen by 0.03 mm and fibres at layer AB shorten by 0.09 mm is 20 mm gauge length as shown in the figure. Taking E-2×10 N/mm², the flexural stress at top fibres would be CD A B 50 mm 100 mm (a) 900 N/mm² tensile (b) 1000 N/mm² tensile (c) 1200 N/mm² tensile (d) 1200 N/mm² compressive →→ 75 mm
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Figure P-108 PARTNER Aluminum A=400 mm² Steel A = 500 mm² 2.5 m 2.0 m Bronze A = 200 mm² 1.5 m 2P