The refrigeration system above uses ammonia (NH3) as the refrigerant. Find: Enthalpies at each point of the cycle in kJ/kg • Total refrigerating capacity in TOR • Compressor power in kW ● Heat rejected in kW ● Coefficient of Performance • Draw the P-h Diagram Hint: h₂ = (h₁ + 281.17) kJ/kg

The refrigeration system above uses ammonia (NH3) as the refrigerant. Find: Enthalpies at each point of the cycle in kJ/kg • Total refrigerating capacity in TOR • Compressor power in kW ● Heat rejected in kW ● Coefficient of Performance • Draw the P-h Diagram Hint: h₂ = (h₁ + 281.17) kJ/kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
In a refrigeration cycle, the refrigerant gains heat in the evaporator and in thesuction line. In a certain refrigeration system, R-134a gains 67.8 Britishthermal units per pound (Btu/lb) in the evaporator. It then gains 2.5 Btu/lb inthe suction line. Find in Btu/lb the total heat gained by the R-134a.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. find Wnet, Ec, Ee and the ideal steam rate. Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. PLEASE USE THE STEAM TABLE PROVIDED: https://drive.google.com/drive/folders/15t3WMv7xSTHmwXWXp0X2ZV6aYWhXuRCS?usp=sharing
As shown in the figure, a 260-ft³ tank contains 25 lb of H20 initially at 30 lbf/in2. The tank is connected to a large steam line carrying steam at 200 lbf/in2, 450°F. Steam flows into the tank through a valve until the tank pressure reaches p2 = 100 lbf/in? and the temperature is 400°F, at which time the valve is closed. Steam at Tank 200 lbf/in_². Valve |(1) Initially: 30 lbfin.2, mi = 25 lb (2) Finally: P, lbfin.?, 400°F. 450°F Determine the amount of mass that enters the tank, in Ib, and the heat transfer to the tank from its surroundings, in Btu.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. For 1kg of steam, find Wnet, Ec, Ee and the ideal steam rate. Remember:1. For values taken from the steam tables: Use them as is, do not round off.2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.PLEASE USE THE STEAM TABLE PROVIDED: https://docs.google.com/document/d/1crebk95lXFEAR5d6Y6LymXJNraO9WLgtNjquSlVOvVs/edit
2. The actual specific evaporation of a certain boiler is 10. Factor of evaporation is 1.05. If the heating value of fuel is 30,000 kJ/kg, find the boiler efficiency. 3. Two boilers are operating steadily on 91000 kg of coal contained in a bunker. One boiler is producing 1591 kg of steam per hour at 1.2 factor of evaporation and an efficiency of 65% and another boiler produces 1364 kg of steam per hour at 1.15 factor for evaporation and efficiency of 60%. How many hours will coal in the bunker run the boilers if the heating value of coal is 7590 kcal/kg?
a rigid 3ft ^3 vessel contains R-134 a originally at -20 F and 27.7 percent quality. The refrigerant is then heated until its temperture is 100 F. Calcuate the heat transfer required to do this. Use data from the refrigerant tables. The heat transfer required to heat the refrigerant is _____ Btu.
Two and one-half pounds of air actuate a cycle composed of the following processes; polytropic compression 1-2, with n = 1.5; constant pressure 2-3; constant volume 3-1. The known data are: p1 = 20psia, t1 = 100oF, QR = -1682 Btu. Sketch the p-V and T-S diagram. Compute and tabulate the p-V-T at all state points. Solve for the Wnet, QR, Efficiency and pm.
Referring to the reversible heat pump cycle shown in the figure, p1 = 14.7 Ib/in?, p4 = 20.3 lb/in?, v1 = 12.6 ft°/lb, v4 = 10.0 ft³/lb, and the gas is air obeying the ideal gas model. p4 pi V4 Determine TH, in °R, and the coefficient of performance.
2) The energy consumed by a shower for 30 days is 22kwh. It is known that the resistance of the showerhead is 20 ohms and that its nominal current is 15A. So, what is the time in minutes that the shower was turned on during this period?
Q2/ In simple refrigeration system uses R134a, the evaporator pressure is 0.25 MPa and the condenser pressure is 1. MPa. The evaporator load is 25 TR. Determine the required work to operate the compressor motor in (a) kW, (b) hp. What is the displacement volume of the compressor if the volumetric efficiency is 80%
An otto engine has a clearance volume of 7%. It produces 300 kilowatts ofpower. What is the amount of heat rejected in kW?