A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem

A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an incline angle 0 is 20° on a film of oil 6 mm thickness, as shown below. Assuming a linear velocity profile in the oil. The viscosity of the oil is 0.009 Pa.s. W y Determine the force acting on the block, F. What is the velocity of the block, V?
What is the height of water inside the tank at time 8.97 minutes after the dumping? Show your complete solution and write clearly. Thank you.
A flat area 1.5x106mm² is pulled with a speed of 0.4m/s relative to another plate located at a distance of 0.15mm from it. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity as 1 poise.
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 3.2 N/m? to maintain this speed with using an oil of specific gravity 0.8. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 663050 cm and weight of 67 kN (ENTER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) 1 (a) The dynamic viscosity of the fluid (in Centipoise) The kinematic viscosity of the fluid (in stokes) 1 (b) Specific Weight in (kN/m³) Density of liquid (in kg/m³) Specific gravity of liquid
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 3.2 N/m? to maintain this speed with using an oil of specific gravity 0.7. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 662000 cm3 and weight of 64 kN
Fast pls solve this question correctly in 5 min pls I will give u like for sure Sub A vertical plate is submerged in water and has the indicated shape. Express how to approximate the hydrostatic force against one side of the plate by an integra and evaluate it. Use a Riemann sum.
1.32 A 1.5 in diameter shaft rotates in a sleeve bearing which is 2.5 in long. The radial clearance between (he shaft and the slecve is 0.0015 in, and this is filled with oil having , = 1.$3 x 10-2 lb/ft•s Assuming rotational speed of 62 rpm and a lincar velocity gradient in the lubricating oil, determine the resistive torque due to viscous shear at the shaft-lubricant interface. Ans. 0.0079 ft-lb
A plate of area 2.15 m is pulled with a speed of 0.3 m/s relative to another plate located at 3.5 mm from it. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity as 500 poise.
4. Find the dimensions of an oil storage tank shown below resulting in a minimum cost using optimal conditions. Cost of the lids is $10 per m², the lifelong maintenance of its surface is $80 per m² and the main body tank surface cost is $8 per m². The overall volume is fixed at 60 m³. M Lid 1 Lid 2.
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
1. The density of an oil is 850 kg/m3. Find its relative density (or specific gravity) and Kinematic viscosity if the dynamic viscosity is 5 x 10-3 kg/ms. 2. If the viscosity of water at 70 °C is 0.00402 poise and its specific gravity is 0.978 determine its absolute viscosity in Pa-s and its kinematic viscosity in m²/s and in stokes 3. Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m³, the volumetric oil flowrate is 720 L/min, and the dynamic viscosity of water is 1.2 centipoise
1.The density P Determine how the density varies with pressure along the depth h. The density at the surface of the fluid is of a fluid varies with depth h, although its bulk modulus K can be assumed constant. Po. 2.A circular disc of diameter (D) is slowly rotated with angular velocity of ( w1) in a liquid of large viscosity (u) at a small distance (h) from another moving disc at counter clockwise rotation of (@2), as shown in figure (2). Derive an expression of torque (T) necessary to this case. D Figure (2)