Bearing h2 Viscous oil, u Shaft L.

Q: A hydrostatic bearing is to support a load of 1000 Ibf/ft of length perpendicular to the diagram.…

A:

Q: Oil is flowing at 0.015 m^3/s in the system shown below. Oil Specific Weight = 8.80 kN/m^3 Oil…

A: Given data: Here, Q represents the flow rate, w represents the specific weight, ν represents the…

Q: Prob. 9: A 35 N plate of metal having dimensions 1.2 m × 1.2 m x 2mm is to be lifted up with a…

A: Given:Area,A=1.2*1.2 m2v=0.14 m/sviscosity, μ=21.6 poise

Q: A square metal plate 1.8 m side and 1.8 mm thick weighing 60 N is to be lifted through a vertical…

A:

Q: Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If…

A:

Q: Problem 5. A thin oil film (u= 0.80 N - 8/m2.p=865 kg/m') of height h = 5.0 mm is squeezed between…

A: Given, Fluid Viscosity μ=0.8 Ns/m2 Density ρ = 865 kg/m2 Height h = 5 X 10-3 m Velocity of bottom…

Q: turbulent flow of a fluid in 0.6m diameter pipe, the velocity 0.15m from the wall 2.7m/s. Estimate…

A:

Q: Two parallel plates, one moving at 4 m/s and the otherfi xed, are separated by a 5-mm-thick layer of…

A: Given data           Velocity 'v'=4m/s           thickness 'dy'=5 mm          Specific gravity…

Q: 2. The pressure drop needed to force water through a horizontal 2.5 cmdiameter pipe is 4kPa, for…

A: Shear stress variation is linear from center axis of the pipe,

Q: The pipe bend shown in the figure is in a horizontal plane. A fluid of weight density 8.615 kN/m?…

A: Given Data The weight density of the fluid is: The inlet velocity of the fluid is: The pressure at…

Q: Water flows in a pipe at 0.015 m³/s. The pipe is 50 mm bore diameter. The pressure drop is 13 420 Pa…

A:

Q: Two smooth pipes, each having a mass of 300 kg, are supported by the forked tines of the tractor in…

A:

Q: Head loss to sudden enlargement, (ii)   Pressure loss across the enlargement (p1-p2).

A: For solution refer below images.

Q: Homwork-3 PH-1 Two smooth pipes, each having a mass of 300 kg, are supported by the forked tines of…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A smooth pipe of 100 mm diameter and 1000 m long is carrying water at the rate of 10 litres/sec. If…

A:

Q: A smooth pipe of 100 mm diameter and 1000 m long is carrying water at the rate of 10 litres/sec. If…

A:

Q: Please answer the attached file

A: Given data The specific gravity of oil is SGoil=0.87. The kinetic viscosity of the oil is…

Q: Lubricant temperature = 60°C Ambient temperature = 15°C Bearing pressure in pump = 1.2 MPa Heat…

A:

Q: A shaft of diameter 74.90mm rotates in a bearing of diameter 75.03mm and of 75mm length. The annular…

A:

Q: Water steadily through a reducing pipe bend. Krown conditions are p1 850 3 kPa atsolute, D1 -25 cm,…

A:

Q: Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3…

A:

Q: A 120 mm diameter shaft is rotating at 280 rpm in a sleeve of 128 mm internal diameter and 800 mm…

A:

Q: Q6/ A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between…

A: Given data: The diameter of the circular plate is d=12 in=0.3048 m The gap between the plate is…

Q: Given that: • Pipe diameter: 0.450 m • Crude oil: Kinematic viscosity = 0.0000232 m2/s • Water:…

A: Given d=0.45mγoil=0.0000232 m2/sμwater=9.2×10-4N-Sm2ρwater=1000 kg/m3

Q: 1.A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing .…

A:

Q: Q1: An oil (u = 0.083 N.sec/m2) flows between two inclined fixed and parallel plates %3D 6mm and 1…

A:

Q: An oil of viscosity 0.8 Pa-s and specific gravity 1.2 flows through a horizontal pipe of 80 mm…

A: Given                 Viscosity = 0.8 Pa.s      Specific gravity = 1.2            Diameter, d = 80…

Q: .A cylindrical shaft of radius 4 cm is rotating at a speed of 30 rad/s in a cylindrical bearing .…

A: Given, Rotating speed ω=30rad/s Radius of the shaft r=0.04m Length of the shaft L=0.1m Clearance h=…

Q: The pipe in the figure is discharging gasoline to the atmosphere. The static pressure in the…

A:

Q: Sketch the velocity, velocity gradient and shear stress profile for a fluid moving past a solid…

A: due to no slip phenomenon, we observe a velocity profile and shear stress on the wall

Q: A bar with a circular section of diameter D1=218 mm moves axially inside a bearing with diameter…

A: Given data: D1=218 mmD2=223 mmL=0.5 mμ=30x10-3 Pa.sV=0.9 m/s Need to determine the value of F needed…

Q: Two parallel plates, one moving at 4 m/s and the other fixed, are separated by a 5-mm-thick layer of…

A: Given     kinematic viscosity = 1.25 x10-4 m2/s           specific gravity =  0.80

Q: Requirements If the velocity profile of a fluid over a flat plate is parabolic with free stream…

A:

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

A:

Q: Problem 7: A 7.5cm diameter shaft rotates at 0.1m/s constant velocity between two plates as in the…

A:

Q: Medium oil with kinematic viscosity 6.10x10^-6 m²/s, flows through a straight pipe at a rate of 6.0…

A:

Q: 5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody…

A: Option (D) is true. The lines for different relative roughness in the turbulent regime  correspond…

Q: Example 1.10. A 400 mm diameter shaft is rotating at 200 r:p.m. in a bearing of length 120 mm. If…

A:

Q: Please answer the following question

A:

Q: A hydrodynamic journal bearing is subjected to 2000 N load at a rotational speed of 2000 rpm. Both…

A: Given:bearing bore diameter, d=40 mmradius of bore=20 mmradial clearance, c=20 μm or 20×10-3…

Q: (2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe.…

A: This problem is solved by using iterations by assuming the pipe diameters. Write the given data.…

Q: 1. A pipe is 25 km long and 80 mm bore diameter. The mean surface roughness is 0.03 mm. It carries…

A: Answer: ◆ The friction coefficient: Cf = 0.0083 ◆ The friction head: hf = 3075 m

Q: A 1.5 in diameter shaft rolates in a sleeve bearing which is 2.5 in long. The radial clearance…

A: Given: d=1.5 inl=2.5 inrc=0.0015 inμm=1.53×10-2lbm/ft.sN=62 rpm

Q: Diameter 60 mm, length-to-diameter ratio 1, bearing clearance 0.12 mm and radial load carried ISO…

A:

Q: A cylinder of weight ( 90 N) slides in a lubricated pipe as shown in the figure . The clearance…

A: Given-Data:- Weight = 90N Clearance =0.025mm Viscosity of oil =6.6×103 Pa.s Speed =6.12m/s…

Q: A cone-and-cup viscometer (see Fig. P3) is used to measure the viscosity of an oil which fills the…

A: