A single-phase bridge type full-wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L/ R) >T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below are given. Vs (t) = 311sin (2n50t) V Note: T=0.02s is the period value of the voltage source. R and L values do not matt er in solving the problem. a. What is the value of the overlap angle in radians? b. Find the effective value of the output voltage.

A single-phase bridge type full-wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L/ R) >T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below are given. Vs (t) = 311sin (2n50t) V Note: T=0.02s is the period value of the voltage source. R and L values do not matt er in solving the problem. a. What is the value of the overlap angle in radians? b. Find the effective value of the output voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A single phase bridge type full wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L / R) >> T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below Re given. V,) = 311sin(2750r)V| Note: T= 0.02s is the period value of the voltage source. R and L values do not matter in solving the problem. A; What is the value of the overlap angle in radians? B; Find the effective value of the output voltage
The following three-phase rectifier has a three-phase source of 240 V rms line-to-line, load is a 20-92 resistance in series with a 40-mH inductance. Determine (a) the dc level of the output voltage, (b) the dc and first ac term of the load current, (c) the average and rms current in the diodes, (d) the rms current in the source, and (e) the apparent power from the source. Van + V b₁¹ + 11 Ven + UN VD₁ D₁ + a DA D3 b D6 D5 C D₂ Load Vo
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
Draw circuit diagram of a full-wave controlled rectifier and draw the wave shapes of output voltage and current for R-L load with sinusoidal input. You have to design a full-wave AC to DC converter circuit to have output average voltage of 40 and 50 W power to a 100 Ω resistive load from a source of 60 V. Is the design feasible? Why?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
I need some help with this problem. I need to create a power supply from 110v 60hz to regulated an output between 6 and 9 v. the image is the desire circuit to acomplish the possible solution. The resistor after the bridge rectifier will work as a surge protector or current limiter for the zener diode. the other is the Load resistor. I need some sort of calculations to prove the specific values for the components to operate according to the specs that I already explain. I know the capacitor will smooth the ripple voltage etc... but I need some guidance to get actual values
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
A DA Vm sin cor For the following single-phase full-wave diode rectifier, Vm = 311 V, R = 1 N, L = 0.002 H and the source frequency is given as 50 Hz. Welding current Find the THD. Note: You can consider calculating the effective value of the welding current and the effective value of the fundamental wave of the welding current. ww