A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of shaft between bearings is 450 mm. Neglecting the effect of stress concentration, find the minimum diameter of shaft. Given that Endurance limit = 600 MPa; surface finish factor= 0.87; size factor = 0.85; and factor of safety=1.6. [Ans. 35 mm]

A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of shaft between bearings is 450 mm. Neglecting the effect of stress concentration, find the minimum diameter of shaft. Given that Endurance limit = 600 MPa; surface finish factor= 0.87; size factor = 0.85; and factor of safety=1.6. [Ans. 35 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

d = 1.25 inch speed 2200 rpm 12000 Ibf d. Shaft load = 2000 lbf (centered between bearings) Temperature: 170 F Tr Bearing specs: O, = 25 Length ratio= 0.80 clearance ratio: Cd -0.002 2. Hydrodynamic bearings are to be selected for the design shown above. Find the following: eccentricity ratio e eccentricity e in., hmin in., Pavs. Ibf/in, Torsional resistance T, in-lbf, Viscosity n microreyn, Oil type: SAE , power loss o HP
8. Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be taken as 1.5. [Ans. 51.7 mm]
Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
I want right solution plz solve if you know 100% flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling flanges are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the flange thickness is 22 mm, Determine the minimum bolt diameter required to transmit the same torque that the shaft can transmit. What power may be transmitted at 200 rev/ min under steady load conditions?
The induced nominal stress in a machine member is 28 N/mm? and the value of maximum stress near the irregularities is 61N/mm?, the value of stress concentration factor is SCF, K = Bearings are designated by a standard number internationally, the first digit in the bearing number 6409 represents type of the bearing. Select one: O True O False The value of curvature correction factor k; will be . if the spring index is 6. O a. 1.33 O b. 1.08 O c.0.,92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is . N, Take pressure angle as 1420. Pitch point P. Gear driven 02 The radial force is
Q 2. A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of −0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 700 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 30, SAE 40 and SAE 50 lubricants operating at an average film temperature of 60 °C.
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
the shaft and Bols bolts. [Ans. 300 mm; 56 mm] 11. Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the following service conditions: Power to be transmitted = 40 kW; speed of the motor shaft= 1000 r.p.m. ; diameter of the motor shaft = 50 mm ; diameter of the pump shaft = 45 mm. The bearing pressure in the rubber bush and allowable stress in the pins are to be limited to 0.45 N/mm2 and 25 MPa respectively. [Ans. d, = 20 mm; n 6; d, = 40 mm; 1 152 mm] :1.1
6. Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15 kN in compression to 25 kN in tension. The endurance limit is 360 MPa and yield strength is 400 MPa. Take impact factor= 1.25, factor of safety= 1.5, surface finish factor= 0.88 and stress concentration factor = 2.25. [Ans. 35.3 mm]
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 MpaSpeed N in Rpm = 500Power P in kN = 15
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 Mpa Speed N in Rpm = 200Power P in kN = 16
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.