A simply supported cast iron beam of span 4m has cross section as shown in Fig:(3.17). How much uniformly distributed load (including self weight) it can carry safely if the permissible stresses in tension and compression are 20MPA and 60MPa respectively.

A simply supported cast iron beam of span 4m has cross section as shown in Fig:(3.17). How much uniformly distributed load (including self weight) it can carry safely if the permissible stresses in tension and compression are 20MPA and 60MPa respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 03 A 24 ft. axially loaded W12 x 96 column that has the bracing and end support conditions…

A: Given, unbraced length = 28 ft or 336 in Specifications for W12 x 96 : A = 28.2 in2 rx = 5.44 in…

Q: Q5. The span length l, = 11 m that carry a dead load of 25 kN/m (not including beam weight) and a…

A: Reinforcement concrete beam: Reinforced concrete is concrete that has steel fully integrated into it…

Q: 3. A simply supported beam has a rectangular cross section with opening as shown in figure below.…

A: since uniformly distributed load is acting over the whole span given,w=20 KN/ml=4 mtherefore…

Q: A cantilever beam of length L and a cross section with shape factor f supports a concentrated load P…

Q: A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab…

A: Draw Free body diagram Consider the summation of forces in the vertical direction RA+RB=P Consider…

Q: A cantilever beam having a span L of 12 m. carries a concentrated load W of 25 kN at midspan. Assume…

Q: Find and illustrate the resultant of the distributed and concentrated loads acting on the beam. 100…

Q: P kN A B C D 4.5 m 3 m 9 m Figure Q2: A Simply Supported Beam

A: Calculate the reaction at support A and B: Note: due to the symmetry of the structure reaction at…

Q: Problem An I-section shown in Fig. 7.16, is simply supported over a span of 12 m. If the maximum…

Q: A beam of I-section is 25 cm deep and has equal flanges 10 cm broad. The web is 0.75 cm thick and…

A: To Find bending moment M that the I beam will carry.

Q: Determine the maximum safe vertical load W that can be supported by the tripod shown in the figure…

Q: A simply supported W18 x 119 A992 steel beam with 8 meters in length was subjected to a service load…

A: Given Data: Service load = 990kn/m DL to LL ratio = 1:2 length = 7m minimum deflection = 3mm

Q: For the beam and loading shown, determine the magnitude of the vertical reaction at B (lb) provided…

Q: A 6-m simply supported timber beam is to be designed to carry a total uniformly load throughout its…

A: We will use formula and find minimum values and take just greater than minimum value.

Q: the rectangular beam given in figure below has been designed for flexure; design the necessary shear…

A: It is required to determine the factored load. wu=1.2DL+1.6LL=1.240+1.625=88 kNm It is required to…

Q: For the two statically determinate structures shown below, it is required to draw the bending…

A: "It has been asked in the question to draw the shear force, axial force and bending moment diagrams…

Q: 850 Ib /ft 630 Ib /ft A B• 9 ft 6 ft 1. What is the equivalent resultant force cause by the external…

Q: Homework: Beam loaded as shown in Fig. 13. Sketch shear and bending moment diagrams for the beam.…

A: Consider the free body diagram of the beam as shown below.

Q: By using FEM find the slopes at the two supports for the loaded beam Given: E = 200 GPa I = 4 x 106…

Q: Q2: Determine the maximum factored force that can be carried by the simply supported beam shown…

A: simply supported beam is the determinate beam with one end is hinge and other end is roller. the…

Q: Question 2 Compute the maximum service live load (in KN) that can be supported by the beam. O Add…

A: Note: As per Bartleby guidelines only solution of question (2) is provided Service Load: The service…

Q: 3. A simply supported beam has a rectangular cross section with opening as shown in figure below.…

A: Consider the free body diagram of the beam shown below.

Q: Draw shear and moment diagram for the beams loaded as shown, specifying values at all change of…

A: first find reaction forces RA+RC=900+400+60×18MOMENT ABOUT A IS zero3600-RC12+7200+60×1822=0RC=1710…

Q: Determine the load carried by HG, CL, CD and CK

Q: The beam shown below with a length L = 12 m and a rectangular cross section that has a width of b =…

A: ASKED: To determine the maximum allowable value of load P according to the given allowable bending…

Q: Simple supported beam with point load (Pu=100 kN) at mid span, what is the value of shear force at…

A: Option C ( 50 kN) is correct

Q: Given: A simply supported beam with a span of L = 36 ft has a uniformly distributed load of 2000 plf…

A: Consider the free body diagram of the beam as shown below.

Q: Determine the maximum uniformly distributed load that can be loaded for the beam shown if the…

Q: 1450 100 Q:Find strength capacity for a simply supported beam with 6m spin, has a section shown in…

A: the effective width of the isolated t beam need to required for analysis of the beam. which is equal…

Q: A 6 meters long floor beams in a certain building are simply supported at their ends and carry a…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Chemical Engineering .1. Calculate the ultimate load of a propped cantilever, span L, carrying a UDL…

Q: 6) The simply supported beam with given cross-section supports the loads as shown. Determine the…

Q: A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab…

A: Free Body Diagram I=bd312I=250*300312I=5625*105mm4E=200kN/mm2EI=112500kNm2∑Fy=0---(Upward positive…

Q: Question No.06 A simply supported beam of span 8 m is carrying a uniformly distributed load of 4…

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 0.5…

Q: A simply supported beam has a rectangular cross section with opening as shown in figure below. Span…

A: Given: The length of the simply supported beam is 4 m. The uniformly distributed load on the beam is…

Q: Use f'c = 4000, fy=60000. The bending capacity of the beam shown is most nearly: (3) #8 REBAR 12"…

Q: Explain the effect of FOUR (4) support conditions on the effective length of column.

A: The effective length of column is a length between points of contraflexure.

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

Q: A floor sheathing is supported by 100 mm x 250 mm wooden joists spaced at 600 mm on centers with an…

Q: A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab…

A: Given:- t=200mmL=9mb=4msize=250*300mmE=200kN/m2To find:-Slope and deflection at point D

Q: ind the maximum load for a beam which is 10 cm wide and 10 inches deep, with supports 3 meters…

A: Given data, p = 3000 lbs wide = 5 inches deep = 12 inches supports = 12 feet apart…

Q: What is the required thickness t of the steel plates

Q: The steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional…

A: Given Data:Length L=5.8mCross-sectional dimensions:d=400mmbf=210mmtf=14mmtw=7mmAllowable bearing…

Q: A 500-mm-diameter, non-slender, spiral column is symmetrically reinforced with six 25 mm vertical…

A: Diameter of column=500mm Diameter of reinforcement=25mm

Q: 10 A rectangular beam 200mm deep and 300mm wide is simply supported over a span of 8m. What…

Q: 4. Investigate the adequacy of the beam reinforced for tension and compression as shown. The total…

Q: An 8 m simply supported beam supports a uniformly distributed load of w and a 3kN concentrated load…

Question

PLZ IGNORE FIG. 3.13 & 3.16 AND ANSWER THE QUESTION PROPERLY.

A simply supported cast iron beam of span 4m has cross section as shown in Fig:(3.17).
How much uniformly distributed load (including self weight) it can carry safely if the
permissible stresses in tension and compression are 20MPA and 60MPA respectively.
-160mm
-240mm
E 100mm
20mm
10mm
20mm
110mm
10mm
300mm
300mn
10mm
20nm
180mm
20m
Fig: (3.13
Fig: (3.16)
Fig: (3.17)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension in MPa? 240 mm T- W 12 KN/m 60 mm 200 mm 4 m 4m 60 mm 165.856 202.967 105.802 none among the choices
Topic: Basic Formulas Used in Steel Design: (Allowable Stress Design) ASD Problem: A simple beam has a span of 10m and supports a superimposed uniformly distributed load of 20 kN/m. Properties of W450x70 A = 8700 mm² bf = 150 mm tf = 15 mm d =450 mm Ix = 274.7 x10⁶ mm⁴ Iy = 8.47 x106 mm⁴ tw = 10 mm Wb = 70 kg/m a. What is the average shearing stress in the beam? b. Determine the maximum shearing stress in the beam. c. Calculate the maximum bending stress in the beam.
Problems in SI Unita For Problems 5.46 and 5.47, detemine the design moment strengths of the beams shown in the accompanying illustrations if f = 28 MPa and f, = 420 MPa. Are the steel percentages in each case sufficient to ensure tensile behavior, that is, e, 2 0.005? Problem 5.46 effective width = 1800 mm- 100 mm 700 mm 600 mm 4 29 ... 400 mm
Q1:If allowable stresses are o, 165MPa, o, 100MPa T= 70MPa determine max. value of W. M 300mm 100mm Im 4m Im pe T 300mm 100mm
OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.
Determine the force in each member of the truss loaded as shown below. Indicate whether the members are in tension or compression. Summarize your analysis by filling-up the table shown. 300 kN Summary: 3 m Member Internal Force (KN) B AB E D AE BC 5m 400 kN BE CD CE DE - 3 m-3 m
Question 1: For the beam with the section shown below, calculate the following items: A b b b b 4m 5m lokn/m B mm 20¹ 120mm 120mm (a) Support reactions at A and B (b) Shear and Bending Moment Diagrams (c) Section Properties (A and I) (d) Maximum Tension and Compression Stresses due to Bending TZomm 120mm Zomm
Question 5: The frame supports factored loads as shown below. Check if the frame is safe for the applied loads. 10 kN/m 6 m 20 kN/m 6 m t = 9.4mm h = 300 mm A = 7220 mm² Ixx = 161 x 106 mm4 XX Sxx = 897 x10³ mm³ Oy = 350 MPa Ty = 230 MPa
Q1:If allowable stresses are o, 165MPa, o, 100MPa T= 70MPa determine max. value of W. CM 300mm Im 4m Im pe T 100mm 100mm 300mm
The center of gravity of the 800N highway sign is at point G. It has been determined that it can withstand a tensile force of 1200N. Other elements in the system are sufficiently durable. The sign is intended to be connected to the fixed joints D and C and AB rope as shown in the figure. Is such a design correct in terms of resistance? 6m B 2m 8m Al D 6m 2m 2m
Q2:If allowable stresses are ot = 165MPa, oc=100MPa t = 70MPa determine max. value of W. W 150mm 50mm 2m 8m 2m 150mm
96 l a o A:01 امتحان کوز .pdf QI: Determine the forces in all members for the truss shown below and state whether the members in tension or compression? Sm Sm 12m 12m Q2: Find the Forces in members BD, CD nd CE 200 N/m 10 1.Sm