A simply supported beam with overhang at the right support is shown in the Figure 2. Determine the following: a. Maximum moment b. Maximum bending stress c. If the cross-sectional area of the beam is circle with outside diameter and inside diameter of 100 mm and 80 mm respectively, determine the section modulus d. Refer to Item 2b, solve the maximum bending stress

A simply supported beam with overhang at the right support is shown in the Figure 2. Determine the following: a. Maximum moment b. Maximum bending stress c. If the cross-sectional area of the beam is circle with outside diameter and inside diameter of 100 mm and 80 mm respectively, determine the section modulus d. Refer to Item 2b, solve the maximum bending stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment M, = 55 Nm. Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
A simple pin-connected truss is loaded and supported as shown. The load P is 160 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 9 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 6 m, b = 3.75 m, and c = 3 m. Tensile stress is positive, while compressive stress is negative. b D A Answer: OAB OAC = OBC OBD OCD || || II a MPa MPa MPa MPa MPa B C
A beam with a T-section is supported and loaded as shown in the figure. The cross section has width b = 2 1/2 in., height h = 3 in., and thicknesst =3/8 in.(a) Determine the maximum tensile and compressive stresses in the beam.(b) If the allowable stresses in tension and compression are 18 ksi and 12 ksi, respectively, what is the required depth h of the beam? Assume thatthickness t remains at 3/8 in. and that flange width b 5 2.5 in.(c) Find the new values of loads P and q so that the allowable tension (18 ksi) and compression (12 ksi) stresses are reached simultaneously forthe beam. Use the beam cross section in part (a) (see figure) and assume that L1, L2, and L3 are unchanged.
A girder with rhombus cross section, b side length, as shown on figure 2 is used as a simply supported beam over a span of 100*b m with central load of 50kN. Determine: (a) an expression for the bending stress, (b) The value of the maximum bending stresses when b=100 mm. Figure Q2
A beam is of a cross- section in the form of a channel as shown in the figure STR - 2. When subjected to sagging bending moment about X-X axis, the ratio of maximum compressive stress to tensile stress is 7:3. Determine the dimension b. I need answer ASAP. Thank you!
3.2: Find the angle & in the case of stress shown in the figure.
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in figure. A B BO Calculate the shear stress on oblique plane at 0 = 45° A 0.625 MPa C 0.31 MPa F D 1.25 MPa
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. Find the following: A. The cross-sectional dimensions of the beam are also shown. B. determine the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section. Express your answer in MPa rounded to the nearest tenths. C. determine the bending stress at point H (positive if tensile and negative if compressive). Express your answer in MPa rounded to the nearest hundredths. D. determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. E. determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures.
The figure shows a single acting rivet connecting steel plates. Rivet diameter d = 22 mm,plate thicknesses are t1 = 20 mm, t2 = 12 mm, plate width b = 100 mm and e = 38 mm. The shear strength in the material is τem = 100 MPa, the safety stress in pressure and tension is σL = 280 MPa andSince σem = 140 MPa, determine the maximum force P that the joint can safely carry.
If the beam is subjected to an internal moment of M=30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. V Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm 150 mm M 15 mm
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm c. Calculate the maximum tensile stress in section a-a in MPa. d. Calculate the maximum compressive stress in section a-a in MPa.