Answered: What is the total RMR of the sandstone…

Engineering

Civil Engineering

What is the total RMR of the sandstone rock mass? A 50 B 75 C) 87 D) 35

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: One way slabs are those that bend along the short span only while two way slabs are those that bend…

A: Given data in question One way slab Two way slab To find out True or false

Q: What are the typical rock sockets for drilled shaft construction in rock?

A: The drilling of solid rock for the shaft insertion is required heavy and tools are required. Mainly…

Q: How does the vane-shear tests can be performed in borings?

A: Vane shear test is essentially a quick test performed either in laboratory or in the field. This…

Q: find FOS for a slip circle with center on line AB , passing through toe and tangetial to the…

A: Given- ϕ=100C=15 Kpaγ=18.5 Kn/m2

Q: B- Describe standard penetration test and its application in foundation engineering Values of N. 9 =…

A: Brief concept- Standard Penetration Test (SPT)- It is a field test and it is used to determine the…

Q: 1400 3800 4000 3600 BED ROOM KITCHEN 1400 2300 3800 BATHROOM 1500 DINING 3500 LIVING ROOM BED ROOM…

Q: t do you understand by rock mass properties? What are the purposes of rock mass classification? Name…

A: A matrix of rock material and rock discontinuities is referred to as a rock mass. Its…

Q: three locations that could exceed allowed stresses and how to find principle stresses using Mohrs…

A: Three location that could exceed allowed stresses are:- (a) At the junction of flange and web both…

Q: 2m x 6m singular sitting on a sandy ground If the total foundation pressure of a foundation is 150…

A: solved

Q: Calculate the design moments of two-way slab as shown with a dimension of 4 mx 6 m if it is to…

A: Shorter span of slab, S=4mLonger span of slab, L=6mDL=10 KPaLL=3.2 KPaOne short and One long edge…

Q: During the subsurface investigation for design of foundation, a standard penetration test was…

A: The data extracted from the table in the image is for a standard penetration test (SPT) conducted at…

Q: tan-3 0.5. What is the stress created by the footing load at a depth of 5m? *

A: Stress calculation at a depth of 5m:

Q: 1. Determine the value ΔΕ. at each point according to the notes that are under the foundation site…

A: The foundation is a critical stage of building construction; it is the lowest part of the building…

Q: Find the an equivalent resultant force and specify the location (x,y) of the equivalent resultant…

A: Consider the figure,

Q: Q2) Find the increasing stress (Ao) at point A, at depth 6 m below the corner of the footing of…

A: Solution

Q: Following are the design parameters of the retaining wall that you are required to design Height the…

A: Solution: Given: h' = 40 ft SBC = 5000 lb/ft2 γ = 120 lb/ft3 μ = 0.53 φ = 35o

Q: 5. Determine whether the slabs shown is a two-way or one-way and also 3m S-1 approximately find the…

Q: QUESTION 14 The cross section of excavation is: O 7.40 m2 O 4.06 m2 3.58 m2 O None of the answers…

A: Question 14 Cross-section of the excavation = 550 x (250+1100) = 0.55 x (.25+1.1) =0.55 x 1.35 =…

Q: A square 1.5m x 1.5m area loaded with q = 120 kPa is placed on the ground surface of a dry site.…

A: From using the Influence Factor chart using value of m and n as 3.0 we get the value of 0.23 for I.

Q: The figure below shows a soil profile located at a site for a bridge construction. The profile…

Q: Determine the minimum slab thickness of the simply-supported one-way slab with L = 2.5 m. Yield…

A: If a slab is supported only two opposite edges then slab is one way slab. If the slab is supported…

Q: Calculate the ratio of the Ultimate Shear Force to Shear Capacity in two-way shear.

A: The values given in the question are as follows Dead load(DL)=772 kN Live load(LL)+620 kN short side…

Q: 7. A petroleum geologist is interested in a long brand new 2 km roadside outcrop. He is working on…

A: Total length of outcrop=2 km=2000 m Length of segment of outcrop studied=50 m Number of joints in…

Q: Define Presumptive Bearing Pressures. Where does their orgin lies?

A: The presumptive bearing pressure is defined as the the permissible pressure or capacity which is…

Q: Question 52 What is the MAXIMUM elevation variation of anchor rod tops from the foundation? 1. 1 2…

A: In the design of Column base plate, there are variations arise due it's construction in Anchor bolt…

Q: What is the lateral earth pressure induced by the surcharge of 25 kPa at depth = 1.5m? q = 25kPa…

A: GIVEN SOIL STRATA

Q: Q3: For the solid slabs shown in Fig.(3), find the spacing of ( 12 mm ) bars required at the…

A: The slab is an important element in the structure for carrying floor load and another live load that…

Q: All Two simply supported slabs: square and circular. They are istropically reinforced and subjected…

Q: Question 01. Using the Fadum chart provided, calculate the total vertical stress due to 200 kPa…

A: As per our policy we have to solve only the first question. Question 01: Load, q = 200 kPa Depth, Z…

Q: Consider the following Erie stress function. For how much C2 can this function be back as a stress…

Q: A 3.44m x 4.49m footing has a 370 mm column at center with the loads P = 597 kN and My=102.7 kN-m…

Q: The center to center spacing of the beams are shown in the figure. Consider the slab panel…

A: Answer We know that given slab can be classified for one way or two way using ratio of longer span…

Q: each cut volume in earth work must be adjustment for * O bulking shrinkage O both for shrinkage and…

A: Given data: Each cut volume in earth work must be adjusted for. a)bulking b) shrinkage c)both for…

Q: ver rectangular section of RC

Q: (127) 12.7 Refer to Figure 12.10. Given: H = 7 m, y = 18 kN/m³, d' = 25°, c' = 12 kN/m², unit length…

A: Given: H = 7m γ=18 kN/m3 ϕ=25o C = 12 kN/m2 α = 10o

Q: A site is underlain by a granite having the following properties and characteristics:• Average…

A: Average uniaxial compressive strength=260 Mpa RQD=80 Nominal bearing capacity qn=Sa+mbSa+Saσci…

Q: a) Calculate the magnitude of the resultant force b) Calculate the location of the resulting force…

Q: ) Use the following log and determine for section 12342-12358ft: eded equations can be found in the…

Q: What is BEARING CAPACITY ANALYSIS IN SOIL—LOCAL AND PUNCHINGSHEAR CASES

A: The pressures of the construction must be distributed across a broad area, which necessitates the…

Q: assume phi=0 throughout and tension crack filled with water, find FOS. the tension crack is assumed…

A: Given- γ=1800Kg/m3C=39Kpaϕ=0

Q: A retaining wall has failed as shown in the diagram below. A block of soil (shown in yellow) is…

A: Data given Failure plane inclined at 450 to the horizontal Find: Using pole method and analytical…

Q: Find the change in vertical stress at level 3m below the base of footing at Point A. It is to be…

A: We can use Boussinesq's equation of point load to calculate the chage in stress under point A From…

Q: A 1.75 m Area = 800 mm² B 1.25 m C Area = 500 mm² 75 kN 1.5 m D 50 kN P.

A: Determine the deformation of point b in mm

Q: Calculate the number of bars along the short direction side band width

A: We need to first calculate the design bearing pressure using qu =PuA Pu = factored load Pu =…

Q: Determine the stability of the wall in different conditions mentioned down in table and provide a…

Question

What is the total RMR of the sandstone rock mass?
A 50
B 75
C) 87
D) 35

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is RQD? What kind of rock is a rock with RQD = 20?
X 9.81 X 8 X 8 P2 $13.92 KN IM compute the intensities earth pressure cohesionless Fricth what and level saturated and (1 of active & passive of 8m in dey an angle of 18 KN lm 3 of intensities of active pressure if the water ground level ? Take of sand as 22 kN/m³ internal frieth is 34°. balz narzo Shot by SNEHAL @813 a 2.61m sand 30° and unit will be the Passive earth rises to unit w angle of DENT at depth with unit wt the Verti unit soil is k UDL thru 60 17 p= 9 =
State Terzaghi’s principle of effective stress and what is the importance of this principle to geotechnical studies
It is requested to dimension the bending wall (similar to figure 2) in order to resist tipping and slipping, considering parameter values geometric and geotechnical according to the table. v (kN/m³) с (КPа) H (m) q (kN/m?) 18 29 20 Note: use data provided in figure 02 for pre-dimensioning. bo be: 20 cm (mín) bi: (8% a 10%) H B: (40% a 70%) H D: 20 cm (mín) ou (8% a 10%) H P: (10% a 12%) H E: 30 cm (mín) b1 Figure 02: typical section suggested for pre-sizing of bending retaining wall (minimum values)
Determine the reinforcements for given slab systems and draw a sketch to show bar arrangements 44 + -12 cm 3.25 1.50 h=120 mm Q=2.0 kN/m² (for Slabs) Q=5.0 kN/m² (for Balcony) -12 cm 3.35 1.50 0.25 ++ + =12 cm 325 150 0.25 ++ + 12 cm 3.25 3.50 Yconcrete 25 kN/m³ Coverage+plaster= 1.5 kN/m² Materials: C25/S420
The location of trial failure surface on a slope is shown in Figure and the stress components for each slice are listed in Table. Slice Shearing component _(kN.m·') -0.280 -0.227 0.383 3.214 6.543 8.368 9.792 Normal component (kŇ.m*) 1.911 7.745 13.139 16.344 17.625 16.718 12.125 0.486 Length of trial failure surface=11m Soil friction angle 6° Cohesion, c=28kPa No. 1 3 4 6. 4.228 Trial Fallure Surface (a) Compute the driving stress. (b) Compute the stabilizing stress. (c) Analyze the safety of the slope.
Discuss Presumptive Allowable Bearing Pressures
The footing shown in figure below exerts a uniform loadq = 250 kPa. Determine the vertical stress at point A (use influence factors) at the depth of 8m and point B (use Newmark's influence chart, show the foundation on the chart) located at the depth of 5m. Note: see Appendix for relevant charts. Top view: 10 m 5m 5m B 10 m 10 m 5m 5m 10 m Scale line IN= 0.005 [The End]
Question 8 A sample slab section view is shown below: *4 0 10" EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab? What should be the correct reinforcement configuration in plan view for this slab? 10" 10" 10" 10"- #4 bars 10"- 10" 10" 10" #4 bars 10"- # 4 bars 10"-
Why is a minimum thickness of at least ten times the depth of the impression required in the Brinell test
Q4: Use the rectangular loaded area to calculate the increase in vertical stresses at points (A) and (B) due to the loaded area of footing. Choose figure (1) or (2). Top view Top view it. awT CLAY 1 CLAY 1 CLAY 2 10m x 10m 150² INCOMPRESSIBLE Figure (1) B G.W.T ME CLAY 1 CLAY 1 CLAY 2 YA 10mX10m 7-15076 INCOMPRESSIBLE Figure (2)
FDE 006. The square footing shown carries a load of 3500 KN. Assume that the stress below the footing is distributed at a slope 1H:2V. The clay layer is overconsolidated with OCR=2. Q = 3500kN Vd 17.5kN/m'. Sand- Vsat 18.3kN/m³ Ysat 17.1kN/m² eo=1.4 Refer to FDE 006. Determi the settlement of the overconsolidated clay layer. Select the correct response: 101.819 mm 73.624 mm 37.561 mm 86.241 mm Clay 3m x 3m GWT Cs= 0.06 Cc = 0.38 0.6m 0.6m 1.2m 1.2m