A simply supported beam which has 16 mm height and 8 mm thickness is supported by pin at A and roller at F as shown in Figure Q2. Loading are applied at B, C, D and E, respectively. 20 KN 20 kN 20 KN 20 KN 8 x 16 mm E F A B

A simply supported beam which has 16 mm height and 8 mm thickness is supported by pin at A and roller at F as shown in Figure Q2. Loading are applied at B, C, D and E, respectively. 20 KN 20 kN 20 KN 20 KN 8 x 16 mm E F A B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.5.9P: A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force,...

See similar textbooks

Related questions

Q: A uniformly distributed force of C kN/m and a concentrated load of D kN are applied to a cantilever…

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are…

A: Vertical reaction at 'D' needs to be evaluated

Q: Figure Q3a shows a simply supported beam AB with support reactions RA and RB. Two point loads F₁ =…

A: To find : The reaction RA and RB . Given : The forces are F1=35 kN and F2=65 KN. The length are…

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin-…

A: According to the information we have a frame with two members AC and BD that is pinned together at…

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are…

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member AC. 1000 Ib 60 60•…

Q: The overhanging beam is supported by a pin at A and the two-force strut BC as shown in Figure Q4.1.…

A: Draw the FBD of the given question and find the angle between the horizontal line and the member BC.

Q: Q2. Figure Q2 shows the free body diagram of a 10 m long beam AD of uniform cross-section, simply…

Q: A cantilever beam is free of support at point A and is clamped at the point B, as shown in the…

A: It is required to determine support reaction force at B

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

Q: Example 18. The homogeneous bar AB of 300 N is resting as shown in figure Ex.18. Assuming contact…

Q: Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum…

Q: Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A…

Q: 10. The rigid bars shown are separated by a roller and hinged at A and D. Bar AC is supported by a…

Q: An eccentrically loaded foundation is shown in Figure P4.8. Use FS of 4 and determine the maximum…

A: According to the given information, we have γ=17kN/m3c'=0ϕ'=36°by…

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

Q: The reaction at the support B of the beam shown in below figure is 2 EN 3 kN B 45° 2 m 2 m 2 m 3 m 2…

Q: 3. The figure shows a frame supported by pins at A and D and carries a triangular load of maximum…

A: In the given example, member DCB will exert a compressive force at point B. We will consider FBDs of…

Q: A plane frame has a pin support at A androller supports at C and E (see figure). Frame segmentsABD…

A: Given data as per question UDL applied on the BD =1.5 KN/m The horizontal force applied at point B…

Q: Figure Q3a shows a simply supported beam AB with support reactions RA and RB. Two point loads F1 =…

A: In order to calculate the external reactions, first of all we have to use the equilibrium equations…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in Figure: Q 4(b).…

A: Given, dAB = 2 in dBC = 3 in LAB = 30 in LBC = 40 in

Q: Q2: The rigid beam shown in fig2 is held by two vertical rods at A and C. If a 60 KN load is applied…

Q: Example: Body M shown in figure weighs (300 N) and the homogeneous bar BE weighs (60 N). Draw the…

Q: Figure Q3a shows a simply supported beam AB with support reactions Ra and Rs. Two point loads F1 35…

A: Using equilibrium conditions as follow 1. Sum of moment about A point zero 2. Sum of vertical forces…

Q: A uniform steel bar of length 10 m is supported at point A and B using two cables as shown in the…

Q: Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A…

A: Reaction force at support A is RA = 152.5 kN. Reaction force at support B is RB = 187.5 kN.

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are…

A: Take moment about the point D Force acting in the x direction is Force acting in the y direction…

Q: Rod AB is fixed to a smooth collar D, which slides freely along the vertical guide shown in (Figure…

A: Given:- P=65lb w=16lb/ft To find:- a) Nc b) Vc c) Mc

Q: 18 kN A AZ 2 m 4 m B

Q: QUESTION 3 Two vertical forces are applied to a beam as in Figure Q3(a) with the cross section shown…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at…

A: Given:P=50 KNFor BD:L=600 mmE=73 GPaA=1250 mm2For CE:L=400 mmE=200 GPaA=750 mm2

Q: A homogeneous 1.5 kN bar AB carries a 2 kN force as shown in the figure. The bar is supported by a…

Q: The homogeneous beam shown in the figure is suspended by a cable at point B and is pin supported at…

Q: A frame structure is shown in the following Figure. Members ABC and BD are pin jointed to supports…

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member AC. 1000 1b 600…

Q: 2. The structure is connected by a pin joint at point A and by a cable of length L at points B and…

A: The free-body diagram of the above structure is given as, Apply force equilibrium in the vertical…

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

Q: Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and…

Q: (a) Draw the free body diagram and determine the reaction forces at joint A (b) Determine the…

A: for solution refer below images.

Q: The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel…

A: Given that, Cross-section of aluminum bar, A=20 mm2Force applied at C, P=50 kN,Cross-sectional area…

Q: AB rigid bar in the figure, P force acts at point B, which is articulated at point A.…

A: Given that, A1=8 cm2A2=4 cm2E1=E2=E=10 kN/cm2L=100 cm,P=13 kN, Drawing the reaction force in the…

Q: Beam ABC in the figure is loaded as shown. Determine the support reactions. B0KN 20KN/m -30kN 60KN-m…

A: Consider the free-body diagram is shown below, The load due to UDL is given as, =20 kN×2 m=40 kN·m…

Q: A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure.…

Q: A steel pipe (1) is attached to an aluminum pipe (2) at flange B. Both steel pipe (1) and aluminum…

A: Given, Cross sectional Area of the pipes, A1=3600 mm2A2=2000 mm2 Lengths, L1=1.8m and L2=1.4m…

Q: A beam weighing 50 kg is attached to a pin at C and supported by a steel cable OA with Young's…

A: 1) Free body diagram of the given beam is drawn below 2) To find Tension in the steel cable OA we…

Q: Q) The member shown in Figure below is pin connected at A and rests against a smooth support at B.…

A: ∵ΣMA=0 →NB x 0.75 = 60 x 1 →NB= 80N

Q: Figure 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported…

A: Allowable stress of pin is not given to find the diameter of the pin put this value in the…

Q: 10. The rigid bars shown are separated by a roller and hinged at A and D. Bar AC is supported by a…

Q: QUESTION 3 A steel bar AD has a cross-sectional area of 260 mm² is illustrated in Figure Q3. The…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A simply supported beam which has 16 mm height and 8 mm thickness is supported by pin at
A and roller at F as shown in Figure Q2. Loading are applied at B, C, D and E, respectively.
20 KN
20 kN
20 kN
20 kN
8 x 16 mm
E
F
A
B
1 m
1 m
1 m
1m
1m
Figure Q2: Simply suoported beam ACDEFB.
(c)
Draw the shear force diagram (SFD) of the beam and show your calculations.
000

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
A beam ABCD with a vertical arm CE is supported as a simple beam at .1 and D (see figure). A cable passes over a small pulley that is attached to the arm at E. One end of the cable is attached to the beam at point B. The tensile force in the cable is 1800 lb. Draw the shear-Force and bending-moment diagrams for beam A BCD. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations. Repeat part (a) if a roller support is added at C and a shear release is inserted just left of C (see figure part b).
Repeat Problem 6.4-14 but use the configuration of channel shapes and loading shown in the figure. Use P = 250 N.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A T-frame structure is torn posed of a prismatic beam ABC and a nonprismatic column DBF. The beam and the column have a pin support at .A and D, respectively. Both members are connected with a pin at B. The lengths and properties of the members are shown in the figure. Find the vertical displacement of the column at points F and B. Plot axial force (AFD) and axial displacement (ADD) diagrams For column DBF.
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
A sign of weight W is supported at its base by four bolls anchored in a concrete footing. Wind pressure P acts normal to the surface of the sign; the resultant of the uniform wind pressure is force fat the center of pressure (C.P). The wind force is assumed to create equal shear forces F/4 in the y direction at each boll (see figure parts a and c). The overturning effect of the wind force also causes an uplift force R at bolts A and C and a downward force (— R) al bolts B and D (see figure part b). The resulting effects of the wind and the associated ultimate stresses for each stress condition are normal stress in each boll (h — 60 ksi); shear through the base plate (th = 17 ksi); horizontal shear and bearing on each bolt ( tfur = 25 ksi and cr^ = 75 ksi): and bearing on the bottom washer at B (or D) (abor = 50 ksi).
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force, shear-force, and bending-moment diagrams for ABC.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A foot bridge on a hiking trail is constructed using two timber logs each having a diameter d = 0.5 m (see figure a). The bridge is simply supported and has a length L = 4 m. The top of each log is trimmed to form the walking surface (see Fig, b)LA simplified model of the bridge is shown in Fig. g. Each log must carry its own weight w = 1.2 kN/m and the weight (P = 850 N) of a person at mid-span, (see Fig. b). Determine the maximum tensile and compressive stresses in the beam (Fig, b) due to bending. If load h is unchanged, find the maximum permissible value of load ... if the allowable normal stress in tension and compression is 2.5 M Pa.