Solve the problem stated below. Use bond papers and black ball pen. Makeyour solution clear and clean. Draw the FBD.PROBLEMFigure:A homogeneous bar AC with negligiblemass is supported by a pin at A andcablecable BC, which carries a load of 20 kNas shown in the figure.a) Determine the force reaction at A, (PA).b) If the shearing stress is 80 MPa(double shear), determine the pindiameter at A.5 m.3 mpin4 mdouble shear60°20 kN

Answered: Image /qna-images/answer/ce8f42a5-2f6d-451c-87b3-6e619b537ce0.jpg

Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: B A homogeneous bar AC with negligible mass is supported by a pin at A and cable BC, which carries a load of 20 kN cable 5 m. as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 3 m pin 4 m double shear 60° 20 kN

Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: B A homogeneous bar AC with negligible mass is supported by a pin at A and cable BC, which carries a load of 20 kN cable 5 m. as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 3 m pin 4 m double shear 60° 20 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.20P: A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by...

See similar textbooks

Similar questions

A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by the distance b = ISO mm from the line of action of the weight force W. The allowable stresses in the arms are 100 MPa in tension and 50 MPa in shear. If the loaded gondola weighs 12 kN, what is the minimum diameter roof the arms?
A prospector uses a hand-powered winch (see figure) to raise a bucket of ore in his mine shaft. The axle of the winch is a steel rod of diameter d = 0.625 in. Also, the distance from the center of the axle to the center of the lifting rope is b = 4.0 in, If the weight of the loaded bucket is W = 100 lb, what is the maximum shear stress in the axle due to torsion? If the maximum bucket load is 125 lb and the allowable shear stress in the axle is 9250 psi, what is the minimum permissible axle diameter?
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Two steel tubes are joined at B by four pins (dp= 11 mm), as shown in the cross section a—a in the fiaure. The outer diameters of the tubes are dAB= 41 mm and dBC= 28 mm. The wall thickness are tAB= 6.5 mm and tBC= 7.5 mm. The yield stress in tension for the steel is sy = 200 MPa and the ultimate stress in tension is ??U:= 340 MPa. The corresponding yield and ultimate values in shear for the pm are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing R between the pins and the tubes are 260 MPa, and 450 MPa, respectively. Assume that the factors safety with respect to yield stress and ultimate stress are 3.5 and 4.5. respectively. (a) Calculate the allowable tensile force P allowconsidering tension in the tube (b) Recompute P allowfor shear in the pins.(c)Finaly, recomputed Pallowfor bearing between the pm and the tubes. Which is the tubes. Which is the controlling value value of P?