A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft (beam weight is to be included), a uniform service live load of 3 kips/ft, and a concentrated service live load of P. The beam is 30 ft long, and the concentrated load P is located at the mid-span. The beam has continuous lateral support and W27x84 A992 steel is used. What is the maximum permissible value of P in kips for LRFD? Express your answer in three decimal places.

A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft (beam weight is to be included), a uniform service live load of 3 kips/ft, and a concentrated service live load of P. The beam is 30 ft long, and the concentrated load P is located at the mid-span. The beam has continuous lateral support and W27x84 A992 steel is used. What is the maximum permissible value of P in kips for LRFD? Express your answer in three decimal places.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.3P

See similar textbooks

Similar questions

SOLVE please Determine the design bending strength of ISLB 350 @ 486 N/m, considering the beam to be laterally supported. Assume factored design shear force will not exceed 0.6 times the design shear strength of the cross-section. If it is used as simply support beam of unsupported length 5 m then determine the factored distributed load the beam can carry. Use Fe410 grade steel For ISLB 350 @ 486 N/m, section properties are as follows: h = 350 mm; b= 165 mm; t₁ = 11.4 mm; t = 7.4 mm; R₁ = 16 mm; Izz = 13158.3 × 104 mm²; I = 631.9 × 10¹ mm²; Zpz = 851.11 × 10³ mm³; Zez = 751.9 x 10³ mm³
Determine the design strength of the beam shown. Assume fy-345MPa and fc'-21 MPa.
The below figure represents a section of a pre- stressed beam. For a no-tension design where a is the permissible stress in concrete, the total moment carrying capacity is (a) (c) d/2 bd² 6 d/2 bd²oc 3 -b- (b) (d) bd² oc 4 bd²a 12
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
A simply supported beam with a span length of 48 feet is laterally supported at its ends and is subjected to the following service loads: Dead load = 400 lb/ft (including the weight of the beam) Live load = 1000 lb/ft If Fy = 50 ksi, is a W14 × 99 adequate? a) Check the capacity based on the limit state of flange local buckling (2) b) Check the capacity based on the limit state of lateral-torsional buckling (Lb)
A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam) and uniform service live load of 2.5 kips/ft. The beam is 40 feet long, The beam has continuous lateral support, and A572 Grade 50 steel is used. A572 Grade 50 steel has Fy = 50 ksi and Fu = 65 ksi. Is a W30 × 116 adequate from flexure and shear?Check both LRFD and ASD. Is the beam adequate from deflection if it allowsmaximum deflection of L/360 (dead load + liveload)?
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load: Live load = 5 kN/m2 Dead load = 8 kN/m? Beam size 300x500 mm %3D B5 B6 B7 3.6 m |L 4.8 4 m 5m 5m BI B2 B4
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
Using the Yield Strength of Grade 60 Steel, what would be the Maximum load that the 25 mm diameter bar can carry? a 204 kN b 203 kN c 205 kN d 206 kN
RCDA reinforced concrete T- beam, section in Figure 2 (a), is subjected to an ultimate uniformload and concentrated loads as shown in the Figure 2(b). The beam is reinforced with 6-28 mm diameter tension bars at the point of maximum positive moment (at midspan -bars at the bottom), and 3-28 mm diameter tension bars at the point of maximum negativemoment (at the supports - bars at the top) .. The design properties used are: f ‘c = 21MPa and fy = 414 MPa, ; flange width = 650 mm, flange thickness is = 90 mm; webthickness = 250 mm; effective depth = 410 mm.Need to answerQ. Draw the shear and moment diagrams for the given loads;
A W18X 97 steel beam will carry the given loads shown in Figure 1. Using ASD with A-36 steel (Fy = 250 MPa). A. If the beam is laterally supported at the two vertical supports only.a) What is the allowable bending stress in the beam in MPa?b) What is the actual bending stress developed in the beam in MPa?c) What is the actual shearing stress developed in the beam in MPa? B. If the beam is laterally supported at the two vertical supports and at its mid-span.a) What is the allowable bending stress in the beam in MPa?b) What is the allowable shearing stress in the beam in MPa?.Neglect the effect of beam weight.