A simply supported beam has uniform load span of 6.0m. It carries maximum shear force of 125 kN at supports and 0.00 kN at mid span. The size of the beam is 250mmx600mm. The steels reinforcement comprises of 5-20mm dia. Bars of grade Fe-415 placed at an effective cover of 50mm from bottom of the beam. Find the zone of minimum reinforcement and the zone where reinforcement more than minimum shall be required. Find the spacing of shear reinforcement if it consists of two legged 8mm dia bars of grade Fe-415.

A simply supported beam has uniform load span of 6.0m. It carries maximum shear force of 125 kN at supports and 0.00 kN at mid span. The size of the beam is 250mmx600mm. The steels reinforcement comprises of 5-20mm dia. Bars of grade Fe-415 placed at an effective cover of 50mm from bottom of the beam. Find the zone of minimum reinforcement and the zone where reinforcement more than minimum shall be required. Find the spacing of shear reinforcement if it consists of two legged 8mm dia bars of grade Fe-415.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
Question No3 Refer to Fig-III Design Shear reinforcement for the beam shown in figure. fyt =300Mpa. Main steel is 5#6 bars and h is 600 mm & b=300. fc' is 21 Mpa. 30KNim 2KN TKNm 1.25m- 4.25m– -2m- -2m- FIG-III
Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded as shown. 20 mm P KN PKN P KN B 20 mm- B с D L/4 m L/4 m L/4 m Pin support at the NA Midspan at point B Mid span at point D Midspan at the top fiber Roller support at top fiber Section D at the top fiber Section C at +170 mm from the NA L/4 m 20 mm C 250 mm 150 mm 150 mm D A
AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
4- The reduction factor (Ø) is equal to 0.9 if the: Es 2 Ety +0.003 Es S Ety +0.003 Es S Ety 5- The design method which use the factored loads is Working stress method Ultimate design Method - None of above 6- If p< Pb therefore the section is - Under reinforced - Over reinforced - None of above 7- For any given section, if c= 150mm , d = 450mm, the ɛs is equal to - 0.003 - 0.006 None of above 8- If area of steel is 2455 mm² and Ø25 mm the number of bars are -(4) - (5) - (6)
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 60 in². NN K 12-12--12--12--| 50 lips 50 kips 50. ips Figure 1 G xfone
4-1 Figure P4.1 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform ser- vice (unfactored) live load of 1.5 kips/ft. The con- crete strength is 3500 psi, and the yicld strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load and strength- reduction factors from ACI Code Sections 9.2 and 9.3. For the midspan section shown in Fig. P4-1b, compute M, and show that it exceeds Mu- Wo = 14 kips/it plus weight of beam WL - 1.5 kipa/it (a) 20 ft 21.5 in. 24 in. (b) 3 No. 9 bars 12 in. Fig. P4-1
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
Please answer. Thank you. Steel Design - Bracing or Coefficient of Gradient (Cb)
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.