A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler asshown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left sideof handle is measured by the ruler as 5 = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm]CAnswer:kkabWhat is the absolute value of deformation in the spring (at B)?Answer:BAnswer:XmmWhat is the absolute value of the internal force in the spring?What would be the absolute value of the applied force on the handle?NN

a=100mm b=250mm x=200mm k=320N/mm To find deformation of spring, force in spring and value of load P

A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler a shown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left of handle is measured by the ruler as 5c = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm] C Answer: B + k k a b What is the absolute value of deformation in the spring (at B)? Answer: X mm Answer: A What is the absolute value of the internal force in the spring What would be the absolute value of the applied force on the handle N N

A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler a shown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left of handle is measured by the ruler as 5c = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm] C Answer: B + k k a b What is the absolute value of deformation in the spring (at B)? Answer: X mm Answer: A What is the absolute value of the internal force in the spring What would be the absolute value of the applied force on the handle N N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

üz a aplanmadı ) üzerinden etlenmiş y ioruyu etle Н V The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the first moment of area (Q) for the point H (mm) where L=48,2 mm.
Upvote will be given. Please write the solutions legibly. Solve in 2 decimal places. A simply supported 5-meter beam is an S- Beam, S610 x 119. If the beam has no external load, A. What is the reaction of the hinge support of the beam? Express the answer in Kilo-Newton? B. What is the reaction of the roller support of the beam? Express the answer in Kilo- Newton.
Use the force method to find the value of the redundant force RCx. All bar areas are the same. (Ans: RCx = 15.71 k) A B 30 ft· D 60 k 30 ft [T] E 0x00 20 ft
The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 28 k N and x = 3.0 m. Write numerical value only and in 2 decimal places.
*write eligibly *use 3 decimal places all throughout the solution Each member of the frame shown in the figure weighs 50 KN/m. Compute the horizontal and vertical components of the pin pressure at C, D and F.
12'-0" TYP. 6 3 10 12 13 www 19 20 17 8 18 12'-0" TYP. 14 45 P 21 16 Use the diagram shown above. Given P= 300 # Calculate the magnitude of the internal force in Member 18. (Magnitude is a positive value.) Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)
3. The small sphere shown below has held by two wires with tension To. sphere is released from equilibrium. Determine the ratio To/T1, where T1 is the tension in the remaining wire immediately after the other mass of 2kg. It is initially One wire is cut and the small a one is cut. 30 30
PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The machine part ABC is supported by a frictionless hinge at B and a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. The force Pis applied on the wedge to push it to the right. Given, F= 680 N. F 200 mm B -250 mm Problem 08.049.c - Reactions at hinge D The value of the component By Is The value of the component By Is [ 10° Determine the components of the corresponding reaction at B N (Click to select) N(Click to select)
The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a roller connection between the bars at C. Compute the vertical displacement (in mm) of point C caused by the 50-kN load. Express your answer to two decimal places. Do not include the unit. * E = 200 GPa A = 300 mm2 L = 3 m 50 kN 2 m 2 m A В D 3 m 1.5 m
no. 2 A 25mm flat bar shown in the figure is suspended vertically from the large end. If P=20kN is applied at shown. Determine the total change in length of the bar.
The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. Assume b= 11 in, h = 3 in., r = 2 in, R = 3 in. Answer:lo-s=1 b R in.4 h
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-