A series R-L-C circuits consists of resistor of 100 ohms. an inductor of 0. 318H and a capacitor of unknown value. When this circuit is energised by 230 Z 0° V. 50HZ sinusoidal supply. the current was found to be 2. 3 20° amperes. Find (i) value of capacitor in microfarad (ii)Voltage across the inductor and (iii)total power consumed.

A series R-L-C circuits consists of resistor of 100 ohms. an inductor of 0. 318H and a capacitor of unknown value. When this circuit is energised by 230 Z 0° V. 50HZ sinusoidal supply. the current was found to be 2. 3 20° amperes. Find (i) value of capacitor in microfarad (ii)Voltage across the inductor and (iii)total power consumed.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 1RQ: An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in...

See similar textbooks

Similar questions

List the five capacitor replacement rules.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
An inductor and a resistor are in series with a sinewave voltage source. The frequency is set so that the inductive reactance is equal to the resistance. If the frequency is increased, then options: Voltage across the inductor= Source Voltage Voltage across the inductor> Voltage across the resistor Voltage across the inductor= Voltage across the resistor Voltage across the resistor > Voltage across the inductor
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
Show that the voltage division rule for two capacitors in series as in the figure
A 250-V circuit, consisting of a resistor, an inductor and a capacitor in series, resonates at 50 Hz. Thecurrent is then 1A and the p.d. across the capacitor is 500 V. Calculate (i) the resistance (ii) theinductance and (iii) the capacitance Answer:
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.