A series circuit of two pure elements has the following applied voltages and resulting currents of 162.63. sin (314.159t + 36.87°) volts and 35.355 sin (314.159t -16.26°) amperes respectively. Determine the: a. the voltage in polar and rectangular forms; b. the current in polar and rectangular forms; c. the circuit impedance, resistance and reactance;

A series circuit of two pure elements has the following applied voltages and resulting currents of 162.63. sin (314.159t + 36.87°) volts and 35.355 sin (314.159t -16.26°) amperes respectively. Determine the: a. the voltage in polar and rectangular forms; b. the current in polar and rectangular forms; c. the circuit impedance, resistance and reactance;

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Draw the waveform of voltage and current under the following conditions: A current which lags the voltage by 60°. A current which leads the voltage by 60°. A current which is in phase with the voltage
Which of the following is true about all series ac circuits?(a) The voltage across any circuit element is a maximumwhen the current is a maximum in that circuit element.(b) The current at any point in the circuit is always thesame as the current at any other point in the circuit.(c) The current in the circuit is a maximum when thesource ac voltage is a maximum.(d) Resistors, capacitors, and inductors can all change thephase of the current.
8. Liquids with solid impurities a) Have higher dielectric strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average de voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
The ripple factor for pure dc is Answer:
The current through a 15kohm resistor is given below, using Ohm’s Law to find the voltage, convert to polar form, complete the math, then convert back to the waveform at i1 = 3.5sin(2500t) mA and i2 = 2.3sin(200t – 60°) mA