Related questions
Question
thumb_up100%
Transcribed Image Text:EXAMPLE 3-1
Pressure of Saturated Liquid in a Tank
T.°C
A rigid tank contains 50 kg of saturated Iliquid water at 90°C. Determine the
pressure in the tank and the volume of the tank.
T= 90°C
Sat. liquid
70.183 kPA
90
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
This is a popular solution
Trending nowThis is a popular solution!
Step by stepSolved in 4 steps with 1 images
Knowledge Booster
Similar questions
- A vertical, frictionless piston-cylinder device contains a gas at 600 kPa absolute. The atmospheric pressure outside is 100 kPa absolute. The piston has a diameter of 50 mm. a) Determine the mass of the piston. b) If the mass of the piston is now halved ---- what would be the gauge pressure of the gas?arrow_forwardThe absolute pressure of a gas in an enclosed cylinder on a day is 3.67 A low pressure storm comes upthe conditions in the gas cylinder remain unchanged does the absolute pressure of the gas increase, decrease, or remain the same? What about the gauge pressure ?arrow_forwardA simple thermometer is formed by taking a large spherical container of volume 1.13m³ and filling it with an ideal gas. Then, a U-shaped tube is attached that is very narrow so that very little fluid/gas can fit inside the tube. The tube has a small quantity of a fluid of density 1200kg/m³ placed in it. In equilibrium at room temperature - 21.9°C - the height of the fluid on both sides of the U-shaped tube are level. This is illustrated in the image below. What is the temperature of the gas in the spherical container when the left side of the fluid is 13.25cm higher than the right side of the fluid in the U-shaped tube? Atmospheric pressure is 101000Pa. °Carrow_forward
- A 0.527 kg metal cylinder is placed inside the top of a plastic tube, the lower end of which is sealed off by an adjustable plunger. The cylinder comes to rest some distance above the plunger. The plastic tube has an inner radius of 6.56 mm and is frictionless. Neither the plunger nor the metal cylinder allow any air to flow around them. If the plunger is suddenly pushed upwards, increasing the pressure between the plunger and the metal cylinder by a factor of 1.35, what is the initial acceleration ? of the metal cylinder? Assume the pressure outside of the tube is 1.00 atmand that the top of the tube is open to the air.arrow_forwardBalloon angioplasty is a technique to restore blood flow through coronary arteries that have been narrowed by the build-up of plaque. The surgeon threads a catheter into the coronary artery, then inflates a balloon that compresses the plaque against the wall of the artery. Suppose a diseased coronary artery has a diameter of 2.0 mm. To what diameter must it be expanded to increase the blood flow by a factor of 5.0 with no change in pressure?arrow_forwardAssume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?arrow_forward
- The intake in the figure has cross-sectional area of 0.79 m² and water flow at 0.48 m/s. At the outlet, distance D = 180 m below the intake, the cross-sectional area is smaller than at the intake and the water flows out at 9.1 m/s. What is the pressure difference between inlet and outlet? MPa Reservoir Generator building Intake Outlet→arrow_forwardThe four tires of an automobile are inflated to a gauge pressure of 2.0 105 Pa. Each tire has an area of 0.025 m2 in contact with the ground. Determine the weight of the automobile. Narrow_forwardA 0.504 kg metal cylinder is placed inside the top of a plastic tube, the lower end of which is sealed off by an adjustable plunger. The cylinder comes to rest some distance above the plunger. The plastic tube has an inner radius of 5.88 mm and is frictionless. Neither the plunger nor the metal cylinder allow any air to flow around them. If the plunger is suddenly pushed upwards, increasing the pressure between the plunger and the metal cylinder by a factor of 3.03, what is the initial acceleration a of the metal cylinder? Assume the pressure outside of the tube is 1.00 atm and that the top of the tube is open to the air.arrow_forward
arrow_back_ios
arrow_forward_ios