A reinforced concrete T-beam has an effective flange width of 800mm with a slab thickness of 110mm. The effective depth is p0mm and the width of web is 320mm. The beam is reinforced with 6325 sq.mm. Of steel with fy=345 MPa. Assuming fc'=26.50 Pa alculate the service live load at midspan in addition to a total deadload of 8KN/m if the span of beam is 6m.

A reinforced concrete T-beam has an effective flange width of 800mm with a slab thickness of 110mm. The effective depth is p0mm and the width of web is 320mm. The beam is reinforced with 6325 sq.mm. Of steel with fy=345 MPa. Assuming fc'=26.50 Pa alculate the service live load at midspan in addition to a total deadload of 8KN/m if the span of beam is 6m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
A rectangular beam has a width of 283mm and an effective depth of 461mm. It is reinforced with 4-25mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The ultimate moment capacity is ___kN.m.
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 377kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.25m from the support if the length of the beam is 2.57m. Note that the dead load includes the weight of the beam.
Q2 A simply supported beam of cross section 280X 560 overall depth. It spans over a length of 8.5 m. The cross section of the beam has tension steel and compression steel 3-32 mm dia and 2-20 mm dia respectively. Assume the effective cover to steel as 50 mm. Dead load on the beam excluding its self-weight is 24.75 kN/m Imposed Load on the beam is 7 kN/m Take fck = 25 N/mm2 and fyk = 500 N/mm2 respectively Check whether the tension and compression steel provided is adequate to carry the given loads
Question: A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 334kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.89m from the support if the length of the beam is 2.24m. Note that the dead load includes the weight of the beam.
A hall is covered by a beam and slab system with beams placed at 3.0 m centers. The effective span of the beam is 8.35 m. the thickness of the slab is 120 mm. The size of the beam below the slab is 230 mm width and 380 mm depth. The beam is reinforced with two numbers of 32 mm diameter steel rods of grade 415 N/mm2. Compute the Maximum total load/m run, the beam can carry, including its own weight at service stage. Grade of concrete is M 25.
Q4/ Compact the design bending strength to the reinforced concrete beam has a width b=300mm and effective depth d=525mm, fc-20, fy=300MPa. Suppose that the beam design to achieve a maximum bending according to code.
0211 A reinforced concrete one way slab is built integrally with support, consist of two equal spans as shown in Figure. Design the slab to carry service live load 4.8kN/m² and service dead load of 5.75 kN/m². Assume: fe 28 MPa and fy = 420 MPa and y=24kN/m². 1-Estimate the slab thickness using limitations of ACI-318M 2- Use the ACI-318M moment coefficients to determine the design moments at critical sections of the slab. 3-. Design the first panel at exterior sport only. 4-Find the load transfer to supporting interior beam. M 6m Fig.2 0.3m+ -4.5m- 11 11 -0.3m -4.5m- +0.3m
A Singly Reinforced Concrete Beam has a cross-section of 300mm x 600mm and a span of 6.5 meters. It is reinforced with 5-25mm diameter bar in one row. The concrete clear cover is 40mm and the traverse reinforcement (stirrups) that was used was 12mm. Currently the beam is carrying a uniform load of 18 kN/m for dead load and live load.Given the following properties of beam, determine the maximum additional uniform load that the beam can carry aside from the initial load that was stated.fs = 124 mPafc = 7 mPan = 12
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The magnitude of the Ultimate moment capacity is Blank 1kN.m.