A 1.6-m-long cantilever beam supports a concentrated load of P = 7.2 kN. The beam is made of a rectangular timber having a width of 120 mm and a depth of 280 mm. Calculate the shear stress due to the applied load at a point located d = 76 mm below the top surface of the beam. d 280 mm B 1.6 m 120 mm O 254 kPa O 156 kPa O 183 kPa O 204 kPa O 269 kPa Save for Later Attempts: 0 of 1 used Submit Answer

A 1.6-m-long cantilever beam supports a concentrated load of P = 7.2 kN. The beam is made of a rectangular timber having a width of 120 mm and a depth of 280 mm. Calculate the shear stress due to the applied load at a point located d = 76 mm below the top surface of the beam. d 280 mm B 1.6 m 120 mm O 254 kPa O 156 kPa O 183 kPa O 204 kPa O 269 kPa Save for Later Attempts: 0 of 1 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and loading shown, design the cross section of the beam, knowing that the grade of timber used has an allowable normal stress of 13 MPa. (Round the final answer to one decimal place.) 3 kN/m 2.4 m B The required value of b is C 150 mm mm.
The uniformly distributed live load on the floor plan in Figure P2.4 is 60 lb/ft2 . Establish the loading for members (a) floor beam B1, (b) floor beam B2, (c) girder G1, and (d) girder G2. Consider the live load reduction if permitted by the ASCE standard.
A simply supported wood beam of length L = 10 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b=4 in. and h = 7 in. If the allowable shear strength of the wood is 100 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. A Answer: P = i B lb ہراب y b h
Please answer with complete solution:
A T-beam w/ a flange width of 450 and a thickness of 175 mm has a total depth of 850mm. Thickness of web is 150 mm. The prestressed beam is provided by unbonded tendons with an effective prestress after all losses fse = 1100 MPa fpy 1. 1500 МPа f — 36 MPа. Compute the stress in the prestressed reinforcement at nominal strength if it has a span of 25 m. а. b. Determine the ultimate moment capacity of the beam if it is reinforced with unbonded tendons placed at 120 mm above the bottom of the beam. Aps = 1800mm² What is the ultimate uniform load that may be supported by the beam. (disregard the weight of the member) С.
Design of Concrete beam A rectangular beam has a width of 375mm and has an effective depth of 450 mm. f'c = 25 MPa, Fy = 300 MPa. 1. Determine the moment capacity if it is reinforced with steel area in tension w/ 12-25mmø reinforcement bar. Use 0.9 as moment reduction factor. 2. Determine the depth of stress block if steel in compression As' = 3000 mm² is added with steel covering of 50 mm below the top of the beam. 3. Determine the moment capacity of the beam reinforced for tension and compression. 375 0.85fc' 0.003 450 12-25mm0 bar N.A 265.74 (d-an) T= As Sy Es 184.26
Situation 1: A concrete overhang beam with the section shown is to support a 150 mm thick concrete slab with a tributary width of 2.70 m. The beam also supports a 3.20 m height of 100 mm thick concrete partition wall. Unit weight of concrete is taken to be 24 kN/m³. Determine the dead load in kN per meter length of beam and determine the maximum fiber stresses (tensile & compressive) due to the imposed dead loads. Draw the complete V&M diagrams. 14 b1 300 mm b3 10.0m G1 120 mm 360 mm LIBRARY Situation 2: Shown below is a floor plan of the library, office and balcony at the second floor level of a condo unit. Use the floor live loads for the given areas: Library area, LL = 5.60 kPa; for Office, LL = 3.20 kPa; and for the Balcony, LL = 2.40 kPa. Determine the live load intensity and load condition to be applied on each member (b1,b2, b3, b4, b5, G1, G2, & G3. Determine also the internal shear and internal moment at the midspan of girder G2. BALCONY G2 G3 4.0m b2 b4 1.2 m FLOOR PLAN 8.0m…
Solve for set B.
A simply supported rectangular concrete beam 6m long is reinforced with four-28mm diam tension bars and two-28mm diam. compression bars. The beam has a width of 300mm and overall depth of 400mm. The steel covering to the centroid of reinforcements is 70mm, fc'=30 MPa and fy=418 MPa. a. Draw the stress diagram b. Compute for the Ultimate moment capacity of the beam
Dead Load= 20 kN/mLive Load= 30 kN/mUnit weight of concrete= 23.56 kN/cu.mf'c= 27.6 MPafy= 414 MPaCompute the shear and moment diagram.
A. Calculate the permissible moment capacity of the doubly-reinforced beam shown: Use f'c = 28MPa and fy = 415 MPa. A's = 1850 mm² A₁ = 4820 mm² 250 O ↓ 80 mm 620 mm 700 mm B. Using the same problem above, determine the permissible moment capacity if the compression reinforcement is removed and the depth (d) of the beam was reduced to 500mm. C. Using the same problem above but with the compression reinforcement removed and depth reduced to 500mm, determine the amount of tension steel (As) that will result in an under- reinforced condition (steel yields) type of failure. Express answer in mm2 Open in Acrobal Activate Windows Go to Settings to activate Window
3. A doubly reinforced beam has dimension of 300mmw x 600mmh. It is reinforced with 225mm diam compression bars and 4 25mm diam tension bars. Concrete cover from centroid of steel bar is 60mm. On its section has a bending moment of 300KN-m. Using working stress design method what are the stresses acting on the concrete, compressive and tensile steel bars? N3D8