A reinforced concrete beam has a width of 300 mmand a total depth of 500 mm. It is reinforced with|6-28 mm dia bars as indicated in the figure.fe = 27.1MPA, fy = 414.7 MPa E, = 200,000 MPad=419.83mm500a. Compute the depth of the compression block6-28:mm øb. Compute the stress of steelc. Compute the ultimate moment capacity of the beam2562.5300

Given Data: fy=414.7 Mpa fc'=27.1 Mpa Es=200,000 Mpa It is asked to compute depth of compression…

A reinforced concrete beam has a width of 300 mm and a total depth of 500 mm. It is reinforced with 6-28 mm dia bars as indicated in the figure. fc = 27.1MPA, fy = 414.7 MPa Es = 200,000 MPa a. Compute the depth of the compression block b. Compute the stress of steel c. Compute the ultimate moment capacity of the beam

A reinforced concrete beam has a width of 300 mm and a total depth of 500 mm. It is reinforced with 6-28 mm dia bars as indicated in the figure. fc = 27.1MPA, fy = 414.7 MPa Es = 200,000 MPa a. Compute the depth of the compression block b. Compute the stress of steel c. Compute the ultimate moment capacity of the beam

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
A. Beams Analysis - Determining Moment Capacity for beam (Under-Reinforced, Over-Reinforced, Balanced Conditions) 3 #19 -350 mm- 520 mm 600 mm 80 mm *For the problem above, use f'c = 28MPa and Fy = 414MPa. C. What is the depth of the compression block "a"? d. What is the stress in the steel fs? How about the stress in f's?
0: A tripe-U shear mount used four 10 mm x 60 mm x 100 mm hard rubber blocks. Upon loading, the upper U frame deflected by 1.5 mm. The elastic modulus of rubber is 50 MPa. Determine the Poisson's ratio of the rubber used. 50 kN 60 mm 100 mm 10 mm A. Pressure between the rubber and the wall (MPa) B. Strain of side KL (mm/mm)
Q2: The reinforced concrete Isolated T-Beam shown in Figure 2, carried uniform distribution live load (35 KN/m) and uniform distribution dead load (30 KN/m). Determine the flexural reinforcement to resist the positive moment (only). (Neglect self-weight), use f'c=28 MPa and fr-420 MPa. 750 mm 80 mm 2m+ - 2 m As 250 Figure 2 إضافة ملف 600 mm
A tripe-U shear mount used four 10 mm x 60 mm x 100 mm hard rubber blocks. Upon loading, the upper U framedeflected by 1.5 mm. The elastic modulus of rubber is 50 MPa. Determine the Poisson’s ratio of the rubber used.Determine the pressure between the rubber and the wall.Determine the Strain of Side KL.
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side
I need answer ASAP. Thank u! STR 2 for the tapering of circular cross section which is subjected to point loads as shown. The section AB has a uniform diameter of 60mm and for the section CD, the uniform diameter is 300mm. Determine the load P3 for equilibrium and net change in length of bar. for Take modulus of elasticity of the bar material as E = 200 GPa. Determine the load P for equilibrium. Determine the net change in length of bar.
2. The width and overall depth of a reinforced concrete beam is 400 mm and 700 mm, respectively. The effective depth is 630 mm, f'c-27.6 MPa and fy=414 MPa. If the beam is a balanced section a. Calculate the area of steel in the section in mm². b. Calculate the depth of compression block in the section at failure in mm. c. Calculate the depth of the neutral axis in the section at failure in mm. d. Calculate the ultimate moment capacity of the section in kN.m. e. If the given section is to support the maximum positive moment in a 5-m propped beam loaded with uniformly distributed load Wu over the entire length, calculate the maximum value of Wu without exceeding the capacity of the given section.
1.)Calculate the height of the neutral axis measured from the extreme compression fiber. 2.) Calculate the strength reduction factor for the given beam. 3.) Calculate the design moment for the given beam. Given b=9.25mm d=152.5mm d(prime)=32.5mm L=1.1m WsubD=6.25kn/m WsubL=8.25kn/m 4 25mm tension steel bars 4 12mm compression steelbars FsubC(prime)=28Mpa FsubY=420Mpa
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000