A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self- weight and service live load of 1200 lb/ft, with a 22 ft simple span. Material strengths will be fy = 60 ksi for and fc' = 3 ksi for steel and concrete, respectively. The total beam depth must not exceed 16 in. Calculate the required beam width and tensile steel requirement, using a reinforcement ratio of 0.600.005- Use ACI load factors and strength reduction factors. The effective depth may be assumed to be 2.5 in less than the total depth.

A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self- weight and service live load of 1200 lb/ft, with a 22 ft simple span. Material strengths will be fy = 60 ksi for and fc' = 3 ksi for steel and concrete, respectively. The total beam depth must not exceed 16 in. Calculate the required beam width and tensile steel requirement, using a reinforcement ratio of 0.600.005- Use ACI load factors and strength reduction factors. The effective depth may be assumed to be 2.5 in less than the total depth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
A singly reinforced rectangular beam has a dimension b 310 mm and d = 410 mm Factored moment is equal to 100 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 275 MPa and the reduction factor is 0.9. Determine the required steel area in mm?
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f'c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
The middle of the 5.6 m simple beam has a dimension of 350 mm by 600 mm. On that location, the beam is reinforced with 3-020mm on the top and 7-020 mm at the bottom. The concrete cover to be used is 40 mm. The stirrups used is 12 mm in diameter The concrete strength of the beam is 27.6 MPa. All reinforcement used is Grade 60 (y = 420 MPa). The beam is carrying a superimposed dead concentrated load of 55 kN and an unknown superimposed live load both at the midspan. The unit weight of concrete used is 23.6 kN per cubic meter Determine the unknown concentrated live load that the beam can sustain.
9 A simply supported beam 300 mm wide, 500 mm deep and spans 5.3 m supports a service super imposed dead load of 7 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
i need the answer quickly
using the table below, answer the question
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.
A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 8 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.