If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa:10-mm-dia425 mm@ 200 mm500 mm-275 mm75 mm25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. =kN26. Calculate the nominal shear strength of the stirrups, Vg =kN.27. Calculate the design sectional shear strength of the beam =kN28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. =kN/m29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. =kN/m30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. =kNINPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER

fc'=21 MPafy=280 MPad=425 mmbw=275 mm10 mm 2-legged stiruppsspacing=200 mmAs per the company's…

25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vs = kN. 27. Calculate the design sectional shear strength of the beam = kN

25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vs = kN. 27. Calculate the design sectional shear strength of the beam = kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The design engineer specifies a concrete strength of 31.0 MPa. Determine the required average…

A: Take the standard case s=5. The formula to calculate the average compressive strength is given by,…

Q: Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored…

A: The maximum depth of the neutral axis from the extreme compression fiber, xu,max =…

Q: 1. Determine the area of reinforcing steel required for the T beam shown if concrete compressive…

A: Solution: Given: Mu = 475 kN-m bw = 300 mm tf = 100 mm d = 600 mm bf = 1600 mm fc = 28 MPa fy = 420…

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 403 mm and an over-all…

A: Given Data: The width of a rectangular beam is b=403 mm. The overall-depth of a rectangular beam is…

Q: SITUATION A: AT beam has a property shown below. fy = 420 MPa, f'c = 35 MPa %3D %3D and Es =200,000…

Q: The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/ mm². Its…

A: Given- M25 grade of concretePermissible bending compressive strength-σcbc=8.5 N/mm2It is needed to…

Q: Help

A: Given: steel in tension zone: n = 6 bars dia. = 40 mm Beam section: b = 300 mm h = 585 mm L = 8000 m…

Q: A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial…

A: Given information is Diameter is d=500 mm effective height l0=4.0m From the above information we…

Q: Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the beam…

A: Given

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 410 mm and an over-all…

A: Torsion in beams is caused by the action of shear loads whose application sites do not correspond…

Q: A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive…

A: From the given problem, Positive Bending moment = 78kip f'c = 3200psi span =26ft

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Referenced concrete When designing the same bim Why is the load in the case of moment greater than…

A: Moment plays an important role in the designing of structures including Beams, Slabs etc., To…

Q: A simply supported beam has a section given in (a), with normal-weight concrete compressive strength…

A: Given bw=12''d=24''fc1=4.5 ksifyt=40 ksi Consider the free body diagram; Calculate factored load…

Q: Calculate yield moment for the beam. Assume concrete accepts no tension. Use fc' = 4000 psi and =…

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A 300 mm wide reinforced concrete beam has an effective depth of 450 mm. It is reinforced in the…

Q: The width and depth of a reinforced rectangular concrete beam is 400 mm and 700 mm, respectively.…

A: Steel support is furnishing steel bars with plain cement to make built up concrete In this idea, the…

Q: Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The…

Q: A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the…

A: given data: outside dimension=190 mm ×190 mm×190 mm load=225 KN

Q: 11.) A simply supported 11-m span beam, 300-mm wide by 530-mm deep, is pre-stressed by straight…

Q: 1. A rectangular beam has b = 300 mm and an effective depth of 525 mm. 28th day compressive strength…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Given d' = 80mm b = 250mm d = 500mm - 70mm = 430mm f'c = 21 MPa fy = 350 MPa for 20mm bars fy = 230…

Q: Calculate the area of reinforcement required for the beam.

Q: • A rectangular beam has the dimensions b=250mm, h=650mm, and d=600mm and is reinforced with three…

Q: The prestressed rectangular section shown in cross section in Figure is pretensioned using five low…

A: b = 300 mmd = 430 mmh = 600 mmfpu = 1860 MPafpe = 1140 kN/m2fc = 28 MPaAps

Q: 1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21…

Q: 2nd: A simply supported 14-m span beam, 300-mm wide by 540-mm deep, is pre- stressed by straight…

Q: A hollow concrete masonry unit has an actual dimension of 150mm x 200mm x 400mm (W x H x L). The…

Q: Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36…

A: Given : To Find : Pmax = ?

Q: Using the following details, Design the shear reinforcement along the length of the beam if it is…

A: Shear reinforcement is used to withstand shear forces that are greater than the concrete's shear…

Q: Q2) Calculate and detail the flexural reinforcement for the beam section shown in Fig.2 at the…

Q: 1.) Given the following properties of a rectangular concre strength under the following conditions.…

Q: Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c =…

A: To determine the cracking moment for the prestressed beam sections shown in the figures, we need to…

Q: The maximum load was tested Failure causes every cube in the group Required: 1- Finding the stress…

A: Given:- w/c=0.3load 1 = 967500NLoad 2= 1012500 NLoad 3= 945000N To find:- the stress rate for each…

Q: Considering the nominal shear stress on concrete is fy = 0.83 MPa. Calculate the allowable max…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa:
10-mm-dia
425 mm
@ 200 mm
500 mm
-275 mm
75 mm
25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. =
kN
26. Calculate the nominal shear strength of the stirrups, Vg =
kN.
27. Calculate the design sectional shear strength of the beam =
kN
28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. =
kN/m
29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. =
kN/m
30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. =
kN
INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Solution

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 300 mm Over-all depth, h = 425 mm Tension reinforcements = 5 pcs 28 mm dia Comp reinforcements = 4 pcs 20 mm dia Specified strength of concrete, f'c = 28 Мра Steel yield strength, fy = 345 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.
Calculate the uniform load w (in addition to the beam weight) that will cause the section shown to begin to crack if used as a 28-ft simply supported beam. Use normal weight concrete with L=4000 psi. f = 60,000 psi, E₁=29,000 ksi, and the reinforced concrete weight = 150 lb/ft³. 4 in. 28 ft 4 in. 22 in. 30 in. 2 in. 2 in. 3 #9 ● ||—12 in—-|
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Help 35 minutes
please answer in the nearest 3 decimal numbers
Correct solution
I need the answer quickly
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.