A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.7 MPa in the x-direction and a tensile stress of 17 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. y Wekd Lütfen birini seçin: a. 13.992 MPa/7.08 MPa b. 0.3076 MPa/4.38 MPa C. None d. 0.3076 MPa/7.08 MPa e. 12.923 MPa/6.91 MPa

A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.7 MPa in the x-direction and a tensile stress of 17 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. y Wekd Lütfen birini seçin: a. 13.992 MPa/7.08 MPa b. 0.3076 MPa/4.38 MPa C. None d. 0.3076 MPa/7.08 MPa e. 12.923 MPa/6.91 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Lütfen birini seçin: a. 9.3175 MPa/6.09 MPa b. None c. 0.417 MPa/4.38 MPa d. 0.6256 MPa/6.70 MPa e. 11.874 MPa/6.70 MPa
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. y Weld Lütfen birini seçin: a. 0.417 MPa/4.38 MPa b. None O c. 0.6256 MPa/6.70 MPa O d. 11.874 MPa/6.70 MPa e. 9.3175 MPa/6.09 MPa O O O
Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress tw acting parallel to the weld. (Assume that the normal stress ow is positive when it acts in tension against the weld and the shear stress tw is positive when its acts counterclockwise against the weld). 12.0 MPa Weld 100 mm 250 mm- Figure 1 25 MPa
7. For the stressed element in the following figure, determine (a) the value of ty for which the in-plane shearing stress parallel to the weld is zero, (b) the corresponding principal stresses. Represent the results on Mohr' s circle. 2 MPa Weld line Txy 75° 12 MPa
A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.3 MPa in the x-direction and a tensile stress of 13 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. Weld Lütfen birini seçin: a. 10.664 MPa/5.50 MPa b. 0.3131 MPa/4.93 MPa c. None d. 0.0358 MPa/5.50 MPa e. 9.3175 MPa/6.09 MPa
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, Px = 20 kN, P, = 16 kN, and P, = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a |P, y P: P H K
2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the allowable shear stress is not to exceed 80 MPa. -60 100 -150 All dimensions in mm. Fig. 2 10 kN
A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa
A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 25
Problem 1: A cylindrical pressure vessel with an inner radius of 1.25 m and a wall thickness of 21 mm is subjected to an internal pressure of 8 MPa. Find the normal stress and shear stress along the 45° weld seam. 45° -1.25 m
A rectangular plate (0 =20°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.0 MPa in the x-direction and a tensile stress of 10 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. y Weld Lütfen birini seçin: a. -0.417 MPa/4.38 MPa O b. 9.3175 MPa/5.50 MPa O c.-0.596 MPa/3.85 MPa d. None e. 8.5962 MPa/3.85 MPa
Solve Q7 only 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN W3 100 W2 -150 50 Fig. 2 7) What is the value of polar moment of inertia of all welds about C.0.G? 3890094.64 mm4 4528724.56 mm4 6782459.89 mm4 9875612.79 mm4