B=55 inside diameter = 28.6in wall thickness=0.35 in. allowable normal stress perpendicular to the weld = 18 ksi allowable shear stress parallel to the weld -8 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 3 decimal places

B=55 inside diameter = 28.6in wall thickness=0.35 in. allowable normal stress perpendicular to the weld = 18 ksi allowable shear stress parallel to the weld -8 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 3 decimal places

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1 grid square is 8 MPa, the principal stress, op1, op2 and the normal stress acting on the planes of maximum shear Stress oave, respectively are -------- ---MPa. A-32, 22, -86 C-22, -32, 86 B--86, 22, -32 D-22, -86, -32 24 NO 2 y (T
wall thickness=0.23 in. allowable normal stress B=56⁰ inside diameter = 66 in. perpendicular to the weld = 10.1 ksi allowable shear stress parallel to the weld =4.4 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 1 decimal place y X
QUESTION 4 B=55⁰ inside diameter = 28.6in. wall thickness=0.35 in. allowable normal stress perpendicular to the weld = 18 ksi allowable shear stress parallel to the weld =8 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 3 decimal places Key
Draw the three Mohr’s circles that describe the following state of stress.
USE IMAGE BELOW And Give your answer in in^4
From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be the value of X such that line YWZ is horizontal? Dimension in mm = 293
7. For the stressed element in the following figure, determine (a) the value of ty for which the in-plane shearing stress parallel to the weld is zero, (b) the corresponding principal stresses. Represent the results on Mohr' s circle. 2 MPa Weld line Txy 75° 12 MPa
Please simply sketch the shear stress diagram 0.5 in. 0.6 in. 0.8 in. 0.2 in. 0.6 in. B -6 ksi 36 ksi --
Draw the diagrams for all the sections views, using the dotted outlines as a guide. Assume that the part is steel & consider the two labelled features to be thin supporting ribs.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
Please answer urgesnt, its not 132.3
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl