A rectangular nylon [E = 8 GPa; ?= 0.35; ?= 24 x107 P/°C] plate has a circular hole in its center. At an initial temperature of T;= 15°C, the plate width is b = 260 mm, the plate height is h = 160 mm, the diameter of the central hole is d = 45 mm, and the thickness of the plate is t = 17 mm. At a final temperature of Tf= 52°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate.

A rectangular nylon [E = 8 GPa; ?= 0.35; ?= 24 x107 P/°C] plate has a circular hole in its center. At an initial temperature of T;= 15°C, the plate width is b = 260 mm, the plate height is h = 160 mm, the diameter of the central hole is d = 45 mm, and the thickness of the plate is t = 17 mm. At a final temperature of Tf= 52°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A rectangular nylon [E =8 GPa; v=0.35; a= 23×106/°C] plate has a circular hole in its center. At an initial temperature of T₁ = 22°C, the plate widthis b=310 mm, the plate height is h = 220 mm, the diameter of the central holeis d = 60 mm, and the thickness of the plateist= 18 mm. At a final temperature of T= 59°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. Answers: (a) d = i (b) t= i b d mm mm
A 13 in length of aluminum tubing (with E = 11.4 x 106 psi and  = 12 x 10-6 /deg F) having a cross-sectional area of 1.6 in2 is installed with “fixed” ends so that it is stress-free at 70 deg F. In operation, the tube is heated throughout to a uniform 500 deg F. Careful measurement at the higher temperature indicates that the fixed ends separate to 13.008 in. What loads are exerted on the ends of the tube, and what are the resultant stresses?
3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch. a. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b. Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) c. Find the stress (in psi) induced in the steel bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.
The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
A copper tube having a cross sectional area of 2000 mm2 and a length of 300 mm is rigidly fixed to two rigid caps on its longitudinal ends. Four steel bolts, each having a diameter of 22 mm, are symmetrically arranged parallel to the axis of the tube and are slightly fastened to the rigid caps, as well. The temperature of the assembly is then raised to 70oC. Take the elastic modulus for Copper and Steel as ECU=100 GLa and EST=200 GPa respectively; the coefficient of linear expansion for Copper and Steel as aCU=16x10-67°C and aST=12x10-6/°C respectively. Calculate the load carried by the copper tube and the load carried by each steel bolt
Question 3: The block shown is made of a magnesium alloy for which E=760GPa and 9 =0.35. Knowing that o=157 MPa, determine (a) the magnitude of o, for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
I In a compression test and for a very ductile material similar to copper , the diameter and the length of the specimen before the test were 60mm and 80mm respectively . Find the length , in inches , after the test if the diameter became 120mm . Assume that the density remained unchanged
A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
5. A steel bolt through a 25-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross- sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 106 psi, coefficient of thermal expansion = 6.5 x 10-6/°F For aluminum: E = 10 x 106 psi, coefficient of thermal expansion = 13.0 x 10-6/°F a. Find the thermal deformation (in inches) of the bolt. b. Find the thermal deformation (in inches) of the aluminum tube. c. Find the stress (in psi) induced in the bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.
A cylindrical specimen made of annealed 4135 steel has a diameter of 16 cm and is 12 cm high. It is upset, at room temperature, by open-die forging with flat dies to a height of 4.5 cm. Assuming that the coefficient of friction is 0.23, calculate the upsetting force (forging force) required at the end of the stroke. Take material properties, K=1015 MPa, n=0.17.
A spherical stainless-steel tank having an inner diameter ‘D’, is used to store naturalgas at a pressure of ‘p’. The properties of the steel are as follows: yield stress in tensionis ‘T’; yield stress in shear is ‘S’ and modulus of elasticity is ‘E’. The desired factor ofsafety with respect to yielding is ‘F.S’.Determine the minimum permissible thickness t min of the tank. (D (mm)=620)( p (MPa)=25)( T (MPa)=1000)( S (MPa)=440)( E (GPa)=208)( F.S=3.4)