A pump with 400 mm diameter suction and a 350 mm diameter discharge pipe is to deliver 20,000 liters per minute of 15.6°C of water. Calculate the pump head in meters if suction gage is 7.5 cm below pump centerline and reads 127 mm Hg vacuum and discharge gage is 45 cm above the pump centerline and reads 75 kpa.

A pump with 400 mm diameter suction and a 350 mm diameter discharge pipe is to deliver 20,000 liters per minute of 15.6°C of water. Calculate the pump head in meters if suction gage is 7.5 cm below pump centerline and reads 127 mm Hg vacuum and discharge gage is 45 cm above the pump centerline and reads 75 kpa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft cubed with a discharge pressure of 150 psig. Suction pressure indicates a 2 HG vacuum. The diameter of the suction and the discharge are 5 in. and 4 in. respectively. The pump has an efficiency of 70% while the motor efficiency is 80%. Determine the (a) water horsepower of the pump (b) bhp of pump motor (c) power input to drive the motor.
Question 1: For the setup shown in the figure: H = 20 m f = 0.0012 f = 0.0012 D = 250 mm D = 80 mm L = 50 m L = 50 m f = 0.001 D₁ = 150 mm L = 100 m A. Calculate Q in the 150 mm-diameter pipe B. If the NPSHR of the pump is 3 m. Is it feasible to use the pump? You can use: Patm-101 kN/m², and Pvapor = 3.17 kN/m² H₂ = 10 m Pump Q f = 0.0012 D=80 mm L = 50 m Q₁ = 0.2
At point A where the suction pipe leading to a pump is 2. 50 meters below the pump an open manometer indicates a vacuum of 9 in. of mercury. The pipe is 125 mm in diameter, the discharge is 35 liters per second of oil (sp. gr. = 0. 80). Compute the total head at point A with respect to a datum at the pump.
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A) No Answer among the choices В 24.31 L/s C) 19.28 L/s D 29.05 L/s E 32.56 L/s
Q10.8 Hydraulic conductivity of an aquifer is known to be 8 ft/day, and its dimensions are estimated to be 40 ft thick and 18,000 ft wide. Two test wells drilled one mile apart in the direction of flow encountered the water table al clevations 5,030 t and 5,050 fL. Question: How many gallons of water flow through the aquifer per day? (To at the front of this manual.) o convert 'o gal, see page We've updated our read aloud featur Give it a try here. A Aa
Data measured during tests of a centrifugal pump at 2750 rpm are Parameter Inlet, Section Outlet, Section (2) Gage pressure, p (kPa) Elevation above datum, z (m) 120 500 2.5 Average speed of flow, V (m/s) 2.5 3.5 The flow rate is 15 cu.m./hr. and the torque applied to the pump shaft is 85N.m. Evaluate the total dynamic heads at the pump inlet and outlet, the hydraulic power input to the fluid, and the pump efficiency. Specify the electric motor size needed to drive the pump. If the electric motor efficiency is 85%, calculate the electric power requirement
The pipe connection shown has a series parallel connection. The rate of flow in the pipe 1 is 300 liters per sec. Assuming equal values of f = 0.02 for all pipes. Compute the discharge of pipeline 2 in cu.m per sec. Compute the discharge of pipeline 3 in cu.m per sec. Compute the discharge of pipeline 4 in cu.m per sec.
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
A pump is used to draw water from an open reservoir to an open tank on thetop of a building. The discharge flow rate is 50 lps. The static suction head of the pump is6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suctionline is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in thedischarge line is 6 inches nominal diameter and 65 m long. The fittings and valvesinstalled in the suction line are the following: two 90o standard elbow and one gate valve.For the discharge line, are the following: one check valve, one gate valve, and three 90ostandard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of82 %. Determine: a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
Pump inflow 2. Draw the HGL for the system shown below. The pump flow at A is 100 L/s with a 550 kPa discharge pressure from the pump. The outflow at B is 40 L/s. Determine the outflow (total demand) at point C in litres per second. Assume a value of CH = 100 for all pipes, and that the pipes are all at the same elevation. 30.00 1000.00 1000.00 1000.00 300 Ø B 2000 200Ø D Elevated Storage Outflow Outflow Tank