A pump draws water from a 200 mm suction pipe and delivers it to a 150 mm discharge pipe in which the velocity is 2.44 m/s. At A in the suction pipe, the pressure is -41.37 kPa. At B in the discharge pipe, which is 3 m above A, the pressure is 413.7 kPa. In what horsepower would have to be applied by the pump if there is a total head loss of 10 m? Select one: O a. 55.6 Hp O b. 74.4 Hp O c. 92.3 Hp O d. 33.7 Hp

A pump draws water from a 200 mm suction pipe and delivers it to a 150 mm discharge pipe in which the velocity is 2.44 m/s. At A in the suction pipe, the pressure is -41.37 kPa. At B in the discharge pipe, which is 3 m above A, the pressure is 413.7 kPa. In what horsepower would have to be applied by the pump if there is a total head loss of 10 m? Select one: O a. 55.6 Hp O b. 74.4 Hp O c. 92.3 Hp O d. 33.7 Hp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
Situation # 4: The pump shown draws water from the reservoir A at elevation 10m and lifts it to reservoir B at elevation 60m. The loss of head from A to 1 is two times the velocity head in the 200mm diameter pipe and the loss of head from 2 to B is ten times the velocity head in the 150mm diameter pipe. Determine the relate horsepower of the pump and the pressure heads at 1 and 2 in meters when the discharge is 0.03m/sec. El. G0 m El. 30 m 500 m 200 rm El. O m FUMP
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
A pump draws water from reservoir A and lifts it to reservoir B as showm, The head los from reservoir A to pipe 1 is 3 times its velocity head and the head loss for pipe 2 to reservoir B is 20 times the velocity head. When the discharge is 20 L/s a) Compute the horsepower output of the pump in kW b) Compute the pressure head at pipe 1 c) Compute the pressure head at pipe 2 EL Om pipe 1 150 mm pipe 2 100 mm -EL-20 m EL 240 m
The pump shown draws water from reservoir A at elevation 10 m and lifts it to reservoir B at elevation 60 m. The loss of head from A to 1 is two times the velocity head in the 200 mm diameter pipe and the loss of head from 2 to B is ten times the velocity head in the 150 mm diameter pipe. Determine the rated horsepower of the pump and the pressure heads at 1 and 2 in meters when the discharge is 0.03 m3/sec.
2. A pump discharge 126 of brine (sp.gr.=1.20). The pump inlet, 304.8 mm in diameter is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm of mercury. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? 122 cm. PUMP
At the end of a 0.6 m diameter pipe, the pressures is 270,000 N m-2. The pipe is connected to a 0.3 m diameter nozzle. If the flow rate is 1.1 m3 s-1, determine the total force on the connection.
5. Oil with sp. gr. of 0.88 is being pumped from a lower reservoir to an elevated tank. The pump in the system is 65% efficient and is rated at 160kW. Determine the flow rate of the oil in the pipe if the total head loss from point 1 to point 2 is 5.5m of oil. 150an 200-mm Pump Elev. 160m Elev. 150 m Oil
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A) 29.05 L/s В No Answer among the choices 32.56 L/s D 24.31 L/s E 19.28 L/s
A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?
An 8 hp pump is installed near the reservoir container of oil having a s.g. Of 0.82. The rate of flow of the pipe is 0.014 ?3/s. The pressure at 1 and 2 are -28 kPa and 290 kPa respectively. a. Compute the head added by the pump in meters.b. Compute the output hp of the pump.c. Compute the efficiency of the pump
A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft cubed with a discharge pressure of 150 psig. Suction pressure indicates a 2 HG vacuum. The diameter of the suction and the discharge are 5 in. and 4 in. respectively. The pump has an efficiency of 70% while the motor efficiency is 80%. Determine the (a) water horsepower of the pump (b) bhp of pump motor (c) power input to drive the motor.