A processor uses a serial link to communicate with a keyboard for word processing. A typist using this keyboard can type at rates peaking at 120 words per minute, where a word is 6 characters (including spaces 9600 and punctuation). The characters will be transmitted from the keyboard in 8-bit ASCII with one stop bit and no parity Only consider these and no special characters. The programmer writes setup and polling service routines based on a minimum baud rate, but then finds that the keyboard will only interface at 19.2 Kbaud. Will the polling service routine have to change? Why or why not? Baud Rates 300 600 1200 2400 4800 19200

Booleans are NOT stored as a single bit because simpler for the compiler writer to use a byte rather than a bit a single bit cannot be accessed efficiently on many machines space efficiency is better when using bytes simpler for the programmer to use a byte rather than a bit

Write a procedure, BitComplement, which will complement each bit in the contents of the ax register. For example, after the following code fragment is executed: mov ax, 0011010111000001B call BitComplement 0011 0101 1100 0001 B then the contents of the ax register will be 1100101000111110B (1100 1010 0011 1110 B).

The following addresses of a Little-Endian machine contain the given hex values shown. If a 32-bit integer is stored at address 100, what is its decimal value? Address Value (Hex). 96 25 97 57 98 59 99 75 100 74 101 63 102 67 103 84 104 93

In  8086 ASM 64 bit, how to write assembly code for taking input for a single digit positive number, increment the input number by 2, write the single digit result, decrement the input number by 1 and then finally write the single digit result.

A digital counter is a device that generates binary numbers in a specified count sequence. The counter progresses through the specified sequence of numbers when triggered by an incoming clock waveform, and it advances from one number to the next only during the occurrence of a clock pulse. The counter cycles through the same sequence of numbers continuously so long as there is an incoming clock pulse. You are to build a 3-bit synci. us count-down counter, which is a counter that counts down goes throug.. Linnni states 111 to 000 and back to 111 to repeat the cou. are to use a positive-edge-tgered JK flip-flops. In the first step of the design, you ecu .- Flop inputs (1 column for each flip-flop input) The present state pur uv.. design and should enumerate the count sequence. The next state columns should specif wnicn slale wn cuo next, given the present state. For example, if circuit is in a present state of the nevt ate in a down-count sequence would be 0. You should design the FF…

Question 12 vish    .Write a program in mips assembly that takes an input from a user and converts it to postfix notation and then solve it Example: ((1-3)+5) corresponds to 13-5+ in postfix notation. Only handle inputs containing numbers 0-9 and operators +,-.  Full explain this question and text typing work only     We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line

Write a MIPS assembly program to find the maximum number among three integers. Ask the user to enter the numbers, save the numbers, and perform the operations. Output the max and min numbers. Your solution should work for all input orders (3, 12, 9) or (3, 9, 12), or (12, 3, 9), etc. Example Enter the first number: 3 Enter the second number: 12 Enter the third number: 9 Output (should be exact) The maximum number is 12 and the minimum number is 3.

Consider a 32-bit hexadecimal number stored in memory as follows: Address Value 100 2A 101 C2 102 08 103 1B If the machine is big endian and uses two’s complement representation for integers, write the 32-bit integer number stored at address 100 (you may write the number in hex). Make it fast