A pressure vessel has an internal volume of 0.5 m³ at atmospheric pressure (1.013 bar). It is desired to test the vessel at 300 bar by pumping water into it. The estimated variation in the change of the empty volume of the vessel due to pressurization to 300 bar is 6 percent. Assuming the bulk modulus of elasticity of water as 2 GPa, the mass of water to be pumped into the vessel to attain the desired

A pressure vessel has an internal volume of 0.5 m³ at atmospheric pressure (1.013 bar). It is desired to test the vessel at 300 bar by pumping water into it. The estimated variation in the change of the empty volume of the vessel due to pressurization to 300 bar is 6 percent. Assuming the bulk modulus of elasticity of water as 2 GPa, the mass of water to be pumped into the vessel to attain the desired

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a rotating cylinder test, the inner cylinder is of diameter 0.2 m and the outer cylinder of diameter 0.205 m contains the liquid up to a height of 0.3 m. The clearance at the bottom of the two cylinders is 5 mm. When the outer cylinder is rotated at a speed of 400 r.p.m, the torsion meter attached to the inner cylinder show the value of torque equal to 5886 Nm. Determine the viscosity of liquid.
A rigid container is partly filled with a liquid at 1520 kPa. The volume of the liquidis 1.232 liters. At a pressure of 3039 kPa, the volume of the rigid container is 1.231liters.a. Compute the average bulk modulus of elasticity of the liquid.b. Compute the coefficient of compressibility.c. If the liquid has a density of 1600kg/m3, what is the speed of sound in the medium?
THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.
For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. For question 103B, the girth stress is equal to Girth joint Longitudinal joint Figure 103 15 MPa 7.5 MPa 3.75 MPa О 30 МРа
A 600-mm diameter non-rigid pipe conveys water from a reservoir with a velocity of 2.50 m/s. The flow is suddenly stopped by the closure of a valve situated 200m from the reservoir. Assume that the pressure increases at a uniform rate and that there is no damping of the pressure wave. The pipe has a thickness of 20mm and a modulus of elasticity of 1.40x1011 Pa. The bulk modulus of elasticity of water is 2.20x10° Pa. Which of the following most nearly gives the celerity of the pressure wave? O 1,108.92 m/s O 1,286.47 m/s O 1,222.76 m/s O 1,483.24 m/s
Water from a reservoir flowing through a deformable 600mm diameter pipe with a velocity of 2.5m/s is completely stopped by a closure of a valve situated 400m from the reservoir. Assume that the pressure increases at a uniform rate and that there is no damping of pressure wave. The pipe has a thickness of 20mm. Bulk modulus of water is 2.20x10°Pa and modulus of elasticity of steel is 0.14x10 Pa. Find the water hammer pressure for instantaneous valve closure.
A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus and Poisson's ratio of the material are 150 GPa and 0.1 respectively. Determine change in volume of the block.
A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall thickness of 13 mm. Compute the hoop stress (in MPa) in the wall of the cylinder.
Question 1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the modulus of elasticity (MPa) of the material. Assume the material does not yield. 2. Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure of 1300 psi. The diameter of the vessel is 2 ft, and the stress is limited to 13 ksi.
The thin walled cylinder diameter whose diameter is 6.24 meters and thickness of 15mm. is subjected to external pressure of 2.47MPa and internal pressure of 4.32MPA. What is the longitudinal stress applied in the walls of the cylinders? Choose the nearest answer. (A) 257 MPa (в) 450 MPа 612 MPa (D) 193 MPa (E) 120 MPa
The tank shown in Figure 1.7.5 is fabricated from a steel plate. What minimum thickness of plate may be used if the allowable stress is 15 ksi and the internal pressure is 125 psi.
Calculate the minimum diameter of cylindrical vessel made of 1-inch thick materials that is use to carry a gas at a pressure of 1500psi. The stress is limited to 12ksi.