A power station has a maximum demand of 100 MW and produces 1008 × 10^3 units per day. The power station has three units of 50, 40 and 40 mega watts. The working hours of this unit are as follows. (1) 0 May. Watt unit 20 hours per day (2) 40 May. Watt unit 15 hours per day (3) 40 May. Find watt unit per day for 5 hours : (1) Load factor (2) Plant capacity factor (3) Plant utilization factor (4) Plant use factor

A power station has a maximum demand of 100 MW and produces 1008 × 10^3 units per day. The power station has three units of 50, 40 and 40 mega watts. The working hours of this unit are as follows. (1) 0 May. Watt unit 20 hours per day (2) 40 May. Watt unit 15 hours per day (3) 40 May. Find watt unit per day for 5 hours : (1) Load factor (2) Plant capacity factor (3) Plant utilization factor (4) Plant use factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

7. A power station has to meet the following load demand: Load A 50 kW between 10 A.M. and6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (i) diversity factor (ii) units generated per day (iii) load factor. () 1-43 (ii) 880 kWh (iii) 52-38%]
36ll 3G 1:00 %71 2 523573914... لم يتم الحفظ بعد H.W. 2 A generating station has the following daily load cycle: Time(Hours) 0-6 6–10 10–12 12-16 16–20 20-24 Load (MW) 40 50 60 50 70 40 Draw the load curve, load duration curve and find 1- maximum demand 2- units generated per day 3- average load. 4- load factor.
Q1. If in one cycle (360 degrees), all of instantaneous power falls under positive loops (no negative loops), the load must be: a.) a resistor b.) an inductor or capacitor Explain: Q2. A wattmeter will indicate zero when the current lags (or leads) the voltage by 90 degrees. Explain
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is O 6000 VA O 2000 VA O 4000 VA 8000 VA
A curve is drawm in descending order of load with time. Al1
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power Is O 4000 VA CO 8000 VA O 6000 VÀ O 2000 VA
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
Short term and long term effects of wind energy on power system
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
The following annual data are from a 160 MW steam turbine-generator plant. Gross generation is 780,000 MWH, net generation is 723,000 MWH, operating hours is 7,730, average load is 99.67 MW, and maximum peak load is 160 MW. Determine the load factor
The data of the power system shown in the figure: X= 1.2 p.u. X= 0.15 p.u. 20MVA G1, G2, G3: T, Т, Тз: L1, L2, L3, L4: Ls: Draw the reactance diagram marked on it all the reactance's in per-unit. 11 KV 30MVA 11/66 KV 66KV X= 400 66KV X= 202 T1 L (G1 T3 Ls L4 美 T2 G3 G2