H.W. 2 A generating station has the following daily load cycle: Time(Hours) 0–6 6–10 10–12 12-16 16–20 20-24 Load (MW) 40 50 60 50 70 40 Draw the load curve, load duration curve and find 1- maximum demand 2- units generated per day 3- average load.

H.W. 2 A generating station has the following daily load cycle: Time(Hours) 0–6 6–10 10–12 12-16 16–20 20-24 Load (MW) 40 50 60 50 70 40 Draw the load curve, load duration curve and find 1- maximum demand 2- units generated per day 3- average load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Related questions

Q: 4.A generating station has the following daily load cycle : Time (Hours) 0-6 6-10 10-12 12-16 Load…

A: In the generating system, Daily load curve data are given Find the maximum demand Energy per day…

Q: Give the formula for finding the voltage regulation of a generator. a) % reg = {[(no-load) -…

A: For a good supply voltage regulation should be low. According to IEEE permissible voltage regulation…

Q: 5. Two single-phase transformers are connected in open delta. The rating of each is 15 kVA, 2400/240…

Q: 2/I A 100 MW powers stations delivers 100 MW for 2 hours, 50 MW for 8 hours and is shut down for the…

A: The solution can be achieved as follows.

Q: . A power station is to supply two loads. The daily load curve of two loads are shown in the figures…

A: As per bartleby expert policy, only first three sibparts are to be answered, subpparts are (1), (2-…

Q: Q1. A generating station has the following daily load cycle: 5-10 50 12-16 Time (Hours) Load (MW)…

A: The solution can be achieved as follows.

Q: Q1: A Power station of 10 MW is to supply two regions A and B, The daily of loads are given below.…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: A certain power station has the following daily load cycle:- Time (6-8)am (8-12)am (12-16)pm…

Q: A power station is to supply two loads. The daily load curves of two loads are shown in figure…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: 160 kVA 22 KV 22 KV 20/0.5 KV Generator G X= 9% Line 200 kVA 40 kVA Z- 2 + j5 2 X= 10% X= 8%…

A: Old base values of generator are 160 KVA, 22 KV. New base values are 160 KVA, 22 KV

Q: A generating station has the following daily load cycle :Time (Hours) 0-66-10 10-12 12–16 16-20…

A: In this question we will solve daily load curve .

Q: A generating station has the following daily load cycle: (Mas) Time (Hours) 0– 4| 4-6 6– 10 | 10 –…

Q: • Choose the correct answer: 1. These substations are usually located at the generating stations a)…

A: In a power system, power generated in power station is to be transmitted to load(consumers). When…

Q: Load duration curve Hours 0 500 2000 4500 6000 8760 Mw 50 Load 50 35 30 20 |15 there are two (2) -40…

A: Rating of each generator = 40 MW Energy = power X time Plant load factor = Actual energy generated…

Q: 1) Three scheduled generating units have the following input-output curves: Unit 1: Unit 2: Unit 3…

Q: A single phase 120V AC sourc controls power to a resistve load 202 using integral cycle control. a)…

A: Note: As per our policy, I have attempted the first three subquestions. Given data: The source…

Q: Q1. A certain power station has the following daily load cycle:- Time In hours Load in MW (6-8)am…

A: load duration curve:- it indicates the variation of the load versus time when the load is arranged…

Q: W(1):- A power station has to supply load as following:- Time (hours) Load (MW) 0-6 6-12 12-14 14-18…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: If the generator cost function of three generators are given as: F1 = 484.8 + 7.67P1 +…

Q: 2. Generating station at Musandam has the following load cycle. (Refer the data sheet below).…

Q: orduria Generation owns three generating units that have the following cost functions: Unit A: 15 +…

A: Given Cost FunctionsUnit A: CA=15+1.4PA+0.04PA2 $/hUnit B: CB=25+1.6PB+0.05PB2…

Q: The incremental cost characteristics of two generators delivering 200 MW are as follows: dF₁ = 2.0 +…

A: Given the incremental cost characteristics of two generators, Generator 1 incremental cost…

Q: 6. A generating station has the following daily load cycle: Time (hours) 0-6 6-10 10-12 12-16 16-20…

A: The solution can be achieved as follows. The answer attached with the question is incorrect.

Q: The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base…

A: In this answer let us try to find the base power used in order to get the given per unit impedance…

Q: b) A power station has the following daily load cycle as Figure Q1(b) below: 16-20 20-24 20 Time in…

Q: A generating station has the following daily load cycle: Time (hours) 0-6 6-10 10-12 12-16 16--20…

A: Daily load cycle is given in the table Draw load curves Maximum demand, unit generated per day,…

Q: Q1. A certain power station has the following daily load cycle:- Time In hours (6-8)am (8-12)am…

Q: Consider a Y-connected AC generator with a number of turns per phase of 60 turns. Find the flux per…

A: In this question , we will find flux per pole for generator....

Q: Q2) Three shunt generators operate in parallel and supply a load current of 12000 A, connected…

Q: Q1 :A- A steam power station of 10 MW (plant capacity) supplied a demand of region A and B each of…

A: Total load at different time duration is shown below

Q: Q1: A Power station of 10 MW is to supply two regions A and B, The daily of loads are given below.…

Q: For the system shown in the following figure, draw an impedance diagram in per unit, by choosing 100…

A: To find the impedance diagram of the given network, it is most important to calculate base KVA and…

Q: A generating station has the following daily load cycle : Time (hours) 0-6 6-10 10-12 12–16 16-20…

A: The solution can be achieved as follows.

Q: A generating station has the following daily load cycle : Time 0-6 6-10 10-12 12-16 16-20 20-24…

A: Load curve:

Q: Q1. A certain power station has the following daily load cycle:- Time (6-8)am (8-12)am (12-16)pm…

Q: A generating station has the following daily load cycle :Time (Hours) 0-6 6–10 10–12 12–16 16–2O…

A: Here load vs time is given we need to solve for all.given by ploting load curve

Q: How to solve this one ?

Q: 750kW alternators are operated in parallel. P₁ = 750kW, P₂ = 750kW Speed regulation of one machine…

A: Dear student you have not posted question and you have doubt in solution, so I’m solving your doubt…

Q: 1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a…

Q: A generating station has the following daily load cycle: Time (Hours) Load (MW) 0-5 5-10 10-12 12-16…

A: We can solve the problem in following manner.

Q: . A generating station has a connected load of 40 MW and a maximum demand of 20 MW : the units…

Q: 6. A generating station has the following daily load cycle: Time (hours) 0-6 6-10 10-12 12-16 16-20…

A: Diagram of load curve: (a) Maximum demand=70MW

Q: A generating station has the following daily load cycle : Time (hours) 0-6 6-10 10-12 12-16 16-20…

Q: . A certain power station has the following daily load cycle:- Time (6-8)am (8-12)am (12-16)pm…

Q: 5. A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor…

A: The solution can be achieved as follows.

Q: Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV,…

A: base value 30 KVA and 6.6 KV=0.03 MVAXpu(new)= Xpu(old) ×(MVAnew)(MVAold)×(KVoldKvnew)2

Q: PCF of the station

A: Plant capacity Factor- Plant capacity factor is defined as the ratio of produced amount of…

Q: 5. A generating station has the following daily load cycle: Time in 0 to 6 6 to 10 10 to 12 to 16 to…

A: In this question, Load and time parameters of the generating Station is given, Find the maximum…

Q: Q1: A Power station of 10 MW is to supply two regions A and B, The daily of loads are given below.…

A: The power station capacity is 10MW. The daily loads are,

Q: 7. A power station has to meet the following load demand: Load A 50 kW between 10 A.M. and6 P.M.…

Concept explainers

Magnetic Moment

The magnetic moment is defined as the alignment of a magnet and its strength when the magnet is creating a magnetic field. There are number of examples of the magnetic moment, few are a current carrying conductor in the form of coil, elements at microscopic levels like electrons and many more.

Question

36ll
3G
1:00
%71
2 523573914...
لم يتم الحفظ بعد
H.W. 2 A generating station has
the following daily load cycle:
Time(Hours) 0-6 6–10
10–12 12-16 16–20
20-24
Load (MW) 40
50
60
50
70
40
Draw the load curve,
load
duration curve and find
1- maximum demand
2- units generated per day
3- average load.
4- load factor.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
5. Draw the daily load curve and load duration curve for a power station with any arbitrary loads you like. From the load curve, determine the following. i. Maximum demand ii. Average demand ii. Daily energy consumption
13. A 3-phase, 16 pole alternator has a star connected winding with 144 slots and 10 conductors per slot. The flux/pole is 0.04 wb (sinusoidal) and the speed is 375 rpm. Find the frequency and phase and line e.m.f. The total turns/phase may be assumed to series connected. [50 Hz, 2035 Hz, 3525 V] (Rajiv Gandhi Technical University, Bhopal, 2000)
The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is............... percent. *
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
Generate a conclusion on this following statements: Determine and analyze the voltage regulation characteristics of the alternator with resistive, capacitive, and inductive loading.
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
b) Two alternators are connected in parallel to feed a load together. The no-load frequency of the first alternator is 51.5 Hz and its slope is 1MW / Hz. The no-load frequency of the second alternator is 51.0 Hz and its slope is 1MW / Hz. The total power of the load fed by these two alternators is 2.5MW and the power factor is 0.8. Accordingly, at what frequency does this system work and what are the power values transferred to the load by each alternator.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Load on a small power station is as under. Draw the load curve and calculate 1. Maximum demand 2. Units generated in a day 3. Average demand 4. Daily load factor.