A pn junction diode of unknown material has the characteristic curve shown. It is used in a circuit in which the source voltage is 9 V and the series resistance is 100 N. Use the load line technique to determine the value of lp for the diode Current (mA) 120 100 80 60 40 20 0 2 4 A) ID 47 mA 69 mA B) ID C) ID 55 mA D) ID 43 mA E) ID≈ 65 mA F) Ip≈ 74 mA 6 Characteristic Curve (Diode 3) 8 Voltage (V) 10 12 14

A pn junction diode of unknown material has the characteristic curve shown. It is used in a circuit in which the source voltage is 9 V and the series resistance is 100 N. Use the load line technique to determine the value of lp for the diode Current (mA) 120 100 80 60 40 20 0 2 4 A) ID 47 mA 69 mA B) ID C) ID 55 mA D) ID 43 mA E) ID≈ 65 mA F) Ip≈ 74 mA 6 Characteristic Curve (Diode 3) 8 Voltage (V) 10 12 14

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
There are two LEDS that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the "on" diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V. +8 V Red Green
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Given the following circuit with VDD = 9.5 V, R = 3.2 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. VDD I a. 0 A O b. 0.002766 A c. 0.002969 A d. 2.968750 A e. 2.765625 A R N V₂
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D