(a) Plot the specific heat of water versus the water temperature for temperatures ranging from 80 to 120°C. Add a second curve on the same graph, but use a 50:50 blend of water and ethylene glycol as the coolant. (b) What change in the design of the cooling system would be needed to compensate for the reduced specific heat of the coolant containing antifreeze?

(a) Plot the specific heat of water versus the water temperature for temperatures ranging from 80 to 120°C. Add a second curve on the same graph, but use a 50:50 blend of water and ethylene glycol as the coolant. (b) What change in the design of the cooling system would be needed to compensate for the reduced specific heat of the coolant containing antifreeze?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.1DP

See similar textbooks

Similar questions

Example design a winter air conditioning power plant for a neighborhood of your choice (preheater/final heater andMust be humidification cells). Audible heat loss of the neighborhood is 50 kW, hidden heat gain is 20 kWhave been calculated. 1-) Show the process in the psychrometric diagram. 2-) Calculate the total amount of air circulating in the system 3-) Calculate the amount of water sprayed into the air in the humidifier 4-) Calculate the preheater capacity. 5-) Calculate final heater capacity
With the help of a neat figure discuss the working principle of evaporative cooling system. What are the factors to be considered while designing an evaporative cooling system?
kindly differentiate the canning methods of process in boiling water bath and using autoclave with pressure
kindly help me with this problem Enumerate and explain each briefly the FOUR (4) Properties of the Bernoulli Process
Completely solve and provide the diagram. Box the final answer. Write legibly 4. A single effect water evaporator operating at 125 kPa abs vapor pressure. Motive steam is available for evaporation at 1.0 MPa with 90% vapor content, what is the mean temperature difference?
explain the principle of operation of a cooling tower and neatly sketch section, analyse a crossflow cooling tower.
Question 2: Consider a 3 effects evaporators supplied with live steam (135°c) at 130°c. Inlet sea water temperature to the first effect is 30°c. If the temperatures in the 2nd and 3rd effects are 100°c and 70°c respectively, calculate the amount of distillate per kg of: 1) Supplied steam 2) Inlet sea water Assume, perfect heat transfer, (m./m,= 0.5= Recovery ratio) and vapor gives up latent heat only in each effect (neglect blow). Salinity of outlet brine has a maximum value as twice as that of inlet sea water
Heat-Transfer Coefficient in Single-Effect Evaporator. A feed of 4535 kg/h of a 2.0 wt % salt solution at 311 K enters continuously a single-effect evaporator and is being concentrated to 3.0%. The evaporation is at atmospheric pressure and the area of the evaporator is 69.7 m². Saturated steam at 383.2 K is supplied for heating. Since the solution is dilute, it can be assumed to have the same boiling point as water. The heat capacity of the feed can be taken as cp = 4.10 kJ/kg · K. Calculate the amounts of vapor and liquid product and the overall heat-transfer coefficient U. 8.4-1.
What do you think is the main difference of humidification process using fine mist or steam from liquid water spraying? Its advantages and disadvantages?
Choose the correct answer. Air temperature affects the rate of evaporation because: Temperatures provide heat required for evaporation Temperature controls latent heat of vaporisation Temperature influences the vapour pressure deficit.
Write about the difference in working principle between induced-draft counterflow and rural-draft cooling towers. Make a drawing for cach one. Induced-draft counterflow cooling tower Natural-draft cooling tower Make a drawing below Make a drawing below
Highlight the concise difference between sensible cooling and cooling-dehumidifying process?