74.A cube 2.2 feet on an edge has its lower half of s.g. =1.6 and upper half of s.g. = 0.7. It rests in a two-layer fluid, with lower s.g. = 1.4 and upper s.g. = 0.8. Determine the height h of the top of the cube above the interface. See Figure 33. S.g. = 0.8 s.g. = 0.7 h 2.2 ft s.g. = 1.6 %3D 2.2 h s.g. = 1.4 %3D

74.A cube 2.2 feet on an edge has its lower half of s.g. =1.6 and upper half of s.g. = 0.7. It rests in a two-layer fluid, with lower s.g. = 1.4 and upper s.g. = 0.8. Determine the height h of the top of the cube above the interface. See Figure 33. S.g. = 0.8 s.g. = 0.7 h 2.2 ft s.g. = 1.6 %3D 2.2 h s.g. = 1.4 %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Change the 10kN to 12kN for it to be stable
Use FEM to calculate the temperature at nodes 2 and 3, and the heat at nodes 1 and 4. Assume A is one unit area.
Use FEM to calculate the temperature at nodes 2 and 3, as well as the heat at nodes 1 and 4.area.
Solve the following problems completely, and make a detailed solution. Use ONLY AREAMETHOD in finding the V-M Diagram. Please do the diagram. Thankyou!
Model the problem in terms of a differential equation
Please show with steps principle of superposition
The below shown graph is drawn from the tabulated values of brass which we measured during the experiment of thermal conductivity: (Consider the value of heater power (Q') and the area of cross section (A) of the material from the tabulated values) X-axis 1 unit = 1cm vaxis 1 unit s'c 70- 20- 10- Distance of the test point from the hot end in centimeter Calculate the following: Thermal conductivity of brass Calculated Value quantities Difference in temperature (AT) C° (with sign) Difference in distance between test points (Ax) cm Slope from the graph °C/m (with sign) Thermal conductivity of brass kp W/m°C
Step by step solution pls thank youu
An aircraft wing is modelled by using a specific element type, which is defined by 2 nodes as shown below. Each node of this element has 3 Degrees of Freedom. If the total number of nodes, used for modelling the wing, is equal to 3,760 then calculate the total degree of freedom of the system. Node 1 Your Answer: element Node 2
1. Suppose identical solid spheres are distributed through space in such a way that their centers are lie on the points of a lattice, and spheres on neighboring points just touch without overlapping. (Such an arrangement of spheres is called a close-packing arrangement.) Assuming that the spheres have unit density, show that the density of a set of close-packed spheres on each of the four structures (the "packing fraction") is: fcc: bcc: √√2/6=0.74 √√3/8=0.68 SC: π/6=0.52 √√3/16=0.34 diamond:
The shape function value O is always higher than 1. O is equal 1 at its own node and zero at other nodes. O is always less than 1. O is zero at the centre of the element.
A brick wall 3 m high, 7.5 m wide, and 160 mm thick has a thermal conductivity of 0.7 W/(m.°C). The temperature on the inner face is 25°C, and the temperature on on the outer face is 0° C. How much heat is lost per day through the wall? (Express your answer using three significant figures.) Q = kJ O- Icon Key