The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel connector AB (E = 200 GPa, A= 615 mm²) and aluminum connector CD (E = 70 GPa, A = 525 mm² ). Determine the deformation incurred by connectors AB and CD. Also, calculate the vertical displacement of E. 57 kN 0.5 m 0.3 m E B 0.25 m 0.5 m

The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel connector AB (E = 200 GPa, A= 615 mm²) and aluminum connector CD (E = 70 GPa, A = 525 mm² ). Determine the deformation incurred by connectors AB and CD. Also, calculate the vertical displacement of E. 57 kN 0.5 m 0.3 m E B 0.25 m 0.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The length of the 2 mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 2 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=200GPA, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D 0.3 m | 20 kg 2 mm 0.3 m 0.1 m
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
02 A cast-iron beam has a section as shown in the figure below. The beam is subjected to two concentrated loads of 3kN. The N.A is located at 35 mm from the bottom and that maximum flexural tensile stress =20 MPa. Determine the width (X) of the flange. 20mm 3kN 3kN 120mm 15m 35mm 20mm 2m 3m 2m
Activity 3 Problem Set Question Locate the plastic centroid of the section shown below. Dimensions are in meters. Your reference axes are the leftmost and topmost edge of the flange. 2Ø12 fy = 350 MPa 0.650 1 Ø12@150 stirrups 5Ø25 fy = 390 MPa 0.250 0.450 0.150
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
A wide flange section has the following properties: A=6645 mm2 bf=152.40mm tf=10.80mm d=449.58 mm tw=7.62mm Fy=250 Mpa Compute the plastic section modulus about the major principal axis and the plastic moment about the x-axis. (x 10^3 mm3)
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw - 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.
1. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet DIa 20 mm x=100 mm a. Calculate "P" in KN considering tension failure on gross area b. Calculate "P" in KN considering tension failure on net area c. Calculate "P" in KN considering failure on bearing on projected area. d. Calculate "P" in KN considering failure on shear on rivets e. Calculate "P" in KN considering failure on bearing on block shear f. Calculate the maximum safe load "P" in KN
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm tw = 14 mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 325870000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05