A pipe network consists of pipeline 1 from A to B, then at B is connected to pipelines 2 and 3, where it merges again at Joint C to form a single pipeline 4 up to point D. Pipelines 1,2 and 4 are in series connection whereas pipeline 2 and 3 are in parallel to each other. If the rate of flow from A to B is 10 liters/sec and assuming f=.02 for all pipes, Determine the flow in each pipe and the total head lost from A to D. Pipelines Length (m) 3,000 Diameter (mm) 200 2 2,200 3,200 300 200 4 2,800 400

A pipe network consists of pipeline 1 from A to B, then at B is connected to pipelines 2 and 3, where it merges again at Joint C to form a single pipeline 4 up to point D. Pipelines 1,2 and 4 are in series connection whereas pipeline 2 and 3 are in parallel to each other. If the rate of flow from A to B is 10 liters/sec and assuming f=.02 for all pipes, Determine the flow in each pipe and the total head lost from A to D. Pipelines Length (m) 3,000 Diameter (mm) 200 2 2,200 3,200 300 200 4 2,800 400

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pipes 1, 2 and 4 are connected in series with pipes 2 & 3 parallel to each other.Pipelines Diameter Length Friction Factor1 350mm 2500m 0.022 400mm 4000 m 0.023 300mm 2000 m 0.024 450mm 2500 m 0.02If the discharge of pipeline 2 is 0.05 m^3/s,1. Compute the rate of discharge of pipeline 32. Compute the rate of discharge of pipeline 43. Compute the total headloss of the pipe system
Pipelines 1, 2 and 3 are connected with parallel to each other with pipeline 1 having a diam. of 450 mm, 600 m long, pipeline 2, 400 mm diam., 800 m long and pipeline 3, 500 mm diam., 700 m long. the 3 pipes carries a combined discharge of 0.86 cum/sec. Assuming f = 0.02 for all pipes. Compute the discharge of pipeline 1. Use 3-decimal places. Compute the discharge of pipeline 2. Use 3-decimal places. Compute the discharge of pipeline 3. Use 3-decimal places.
Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33 ft. the pipeline consists of an upstream section, D1= 30 in and L1 = 5000 ft and a downstream section, D2 = 21 in and L2 = 3500 ft. The pipes are concrete (f=0.016) and are connected end to end with a sudden reduction area. Compute the discharge capacity.
A pipe network consist of Pipeline from A to B, then at B, it is connected to pipelines 2 and 3, where it merges again at joint C to form a single pipeline 4 up to point D. Pipelines 1, 2/3, and 4 are in series connection whereas pipelines 2 and 3 are parallel to each other. Pipeline #1 is 3,000m long and 200mm in diameter; pipeline #2 is 2,200m long and 300mm in diameter; pipeline #3 is 3,200m long and 200mm in diameter; and pipeline #4 is 2,800m long and 400mm in diameter. If the rate of flow from A to B is 10 liters/sec and assuming ƒ = 0.02 for all pipes, determine the following: A) Compute the flow in Pipeline 2 in Liters/sec. B) Compute the total head lost, in meters, from point A to D.
Pipelines 1, 2 and 3 are connected with parallel to each other with pipeline 1 having a diam. of 450 mm, 600 m long, pipeline 2, 400 mm diam., 800 m long and pipeline 3, 500 mm diam., 700 m long. the 3 pipes carries a combined discharge of 0.86 cum/sec. Assuming f = 0.02 for all pipes. -Compute the discharge of pipeline 1. -Compute the discharge of pipeline 2. -Compute the discharge of pipeline 3.
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m³/s. Pipe Length Diameter Friction Factor 400 mm 1,800 mm 1,500 mm 2,000 mm 1 0.020 X A 2 в У 2 350 mm 0.018 300 mm 0.022 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
Table 1 shows the data for the network of pipes connecting four reservoirs to a common junction, J. Table 1 8fL r = gπ2p5 4.0 Reservoir Water Reservoir Pipe Level (m) A 50 AJ B 45 BJ 3.0 C 40 CJ 2.0 D 30 DJ 2.0 а) Sketch the pipe network together with the four reservoirs as described above and show the directions of flow based on the initial assumption of the head at the junction J of 41 m. State two hydraulics principles that need to be fulfilled in the analysis of this pipe network. b) Calculate the discharge in each pipe. Compute your answer to two decimal places only.
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m/s. 1 Pipe Length Diameter Friction Factor 1,800 mm 1,500 mm 2,000 mm 0.020 0.018 0.022 400 mm A 2 в у 350 mm 3 300 mm 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
1. A pipe network consists of the following pipes: pipe AB is 20 cm in diameter and 700 meters long; pipe AC is 25 cm in diameter and 800 meters long; pipe BC is 15 cm in diameter and 900 meters long; pipe BD is 15 cm in diameter and 100 m long; and pipe CE is 30 cm in diameter and 50 m long. An inflow of 0.20 cubic meters per second enters the system at junction A and 40% of this discharge flow on pipe AB. If Cw for Hazen-William's Equation is 122 for all pipes, determine the discharges in pipes BD and CE.
Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33 ft. The pipeline consists of an upstream section, D1 section, D2 end with a sudden reduction of area. Assume the water temperature is 68°F. Compute the discharge сарacity. = 30 in. and L1 21 in. and L2 = 3,500 ft. The pipes are concrete (smooth) and are connected end to 5,000 ft; and a downstream
From the given three reservoirs, the elevation of A is 345m, B is at elevation 300m, and C is at elevation 240m. The rate of flow at 1 is 300li/sec. A. Compute the headloss in pipeline 2 B. Compute the discharge in pipeline 3 C. Compute the diameter of pipeline 3 Location of pipe Reservoir A to junction X Length (m) 600 Pipe no Diameter (mm) HAZENS (C) 1 450 120 Junction X to Reservoir B 2 3600 300 100 Junctin x to Reservoir C 3 1250 ? 110