A pin-jointed 2-D truss is loaded with a vertical load of 10 kN as shown in figure. The crosssectional area of the horizontal member is 150 mm² and cross-section areas of the members AC and BC are 200 mm² each. Modulus of elasticity of the truss material is 200 kN/mm². The magnitude of horizontal displacement (in mm, round off to two decimal places) of joint C is. 10 kN 6 m 4.5 m

A pin-jointed 2-D truss is loaded with a vertical load of 10 kN as shown in figure. The crosssectional area of the horizontal member is 150 mm² and cross-section areas of the members AC and BC are 200 mm² each. Modulus of elasticity of the truss material is 200 kN/mm². The magnitude of horizontal displacement (in mm, round off to two decimal places) of joint C is. 10 kN 6 m 4.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm
A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead central point as shown in the figure STRM10. The plate supports a surface load of W in kPa. The point of attachment A is 1.25 m above the plane of the plate. 1.25 m 2 m 2 m Determine the maximum load W (kPa) the tie rods can support if the allowable tensile stress on it is 450 MPa. 1) A. 8.43 С. 10.12 В. 12.83 D. 5.64 2) Determine the elongation of each steel tie rod if W = 8.5 kPa. A. 4.28 mm B. 6.46 mm C. 2.84 mm D. 3.54 mm 3) Determine the vertical displacement of the plate. A. 4.28 mm B. 6.46 mm С. 2.84 mm D. None of the above O 1A 1B 10 1D O 2A 28 O 20 O 20 О ЗА O 3B O 30 O 3D
The frame shown in the figure is carrying a traingular distributed load. Pins at Aand B are forced in single shear while the pin at C is forced in double shear. If the allowabletensile stress of bar BC is 300 MPa and the allowable shear stress of pins is 150MPa;(a) The cross sectional area of BC(b) The required diameters of pins A, B and C as multiples of mm.
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1 m 25KN The thickness of the horizontal member is 15 mm, what will be the value of its bearing stress at A in MPa? Diameter of the pin at A is 20mm.
In the given cross section, the neutral axis relative to the bottom fiber is 63 mm and the moment of inertia with respect to the neutral axis is 30,950 mm4. Shear force is 13 kN and bending moment is -120 N-m. Determine the: -Maximum flexural and shear stress in the cross-section (MPa) 65 mm 33 100 mm 46 mm 50 mm 25 mm ↑
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead central point as shown in the figure STRM10. The plate supports a surface load of W in kPa. The point of attachment A is 1.25 m above the plane of the plate. 1.25 m 2 m 2 m 1) Determine the maximum load W (kPa) the tie rods can support if the allowable tensile stress on it is 450 MPa. A. 8.43 В. 12.83 С. 10.12 D. 5.64 2) Determine the elongation of each steel tie rod if W = 8.5 kPa. A. 4.28 mm В. 6.46 mm C. 2.84 mm D. 3.54 mm 3) Determine the vertical displacement of the plate. A. 4.28 mm B. 6.46 mm C. 2.84 mm D. None of the above