A piece of corroded metal alloy plate (density =4.5g/cm3) was found submerged in ocean. it was estimated that the original area of the plate was 800cm2 and that approximately 7.6Kg had corroded away during the submersion period of 5.3 years. Estimate the corrosion penetration rate for the metal plate?

A piece of corroded metal alloy plate (density =4.5g/cm3) was found submerged in ocean. it was estimated that the original area of the plate was 800cm2 and that approximately 7.6Kg had corroded away during the submersion period of 5.3 years. Estimate the corrosion penetration rate for the metal plate?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cold worked components results in uniform properties of the metal. Select one: True False
ESSAY: Question: What types of corrosion is the most destructive and insidious forms of corrosion?
Using the equation Kica, plot the fracture stress (MPa) for aluminum alloy 7075-T651 versus surface crack size a (mm) for a values from 0.2 mm to 2.0 mm. What is the minimum size surface crack that will cause catastrophic failure?
Tag question Consider the graph below for 3 metals which have been cold-worked. From the graphs, which of the following statements are true? Stress Select one or more: a. C. Strain & A e. B C b. B and C have similar hardness; C has greater brittleness B is softer than C and has nearly similar ductility A is harder than C and is more ductile d. A and B have similar hardness; A has greater brittleness A is harder than C and is less ductile f. B is harder than C but has nearly similar ductility 5 up i A C
An engineer is designing a total hip implant. he intends to make the femoral stem out of titanium and to make the ball component out of stainless steel. Should you be worried about corrosion? If so, what types of corrosion could take place? How do you prevent that? Write your comment.
Topic: Thermal & Torsional Stress The rigid, horizontal slab is attached to two identical copper rods. There is a gap ∆ = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 60 o Use the following data:
A change in temperature can cause a member made of homogeneous isotropic material to change its length why?
Please answer the question with steps An unknown material bar having length of 4.3m has 1m cross sectional area. One end is in contact with 373K Thermal conductivity of the material is 197W/mK. The total rate of heat flow is Joules/second. ....... .... (Calculate up to one decimal point accuracy).
Normally when the creep is considered in materials?
Consider the graph below for 3 metals which have been cold-worked. From the graphs, which of the following statements are true? Stress o Select one or more: □ c. Strain & A e. B a. B and C have similar hardness; C has greater brittleness b. B is softer than C and has nearly similar ductility A is harder than C and is more ductile C d. B is harder than C but has nearly similar ductility A is harder than C and is less ductile f. A and B have similar hardness; A has greater brittleness
Briefly explain/define the following topics. Use drawings and equations if necessary. Galvanic corrosion and its prevention (а) (b) (d) Adhesive and abrasive wear Factors that affect the endurance limit in materials (c) Thermal residual stresses and their origin (e) List the mechanisms for creep deformation in metallic materials. Explain one of them.
How does point defect affect properties of materials? Please answer within 10 mins. 5-10 sentences. Thank you