A path in a digital switched network has a data rate of I Mbps. The exchange of 1,000 bits is required for the setup and teardown phases. The distance between sender and receiver is 5,000 km apart. The propagation speed is given as 2 x 10 ms. Examine the total delay if 100,000 bits of data are involved during the data transfer phase?

A path in a digital switched network has a data rate of I Mbps. The exchange of 1,000 bits is required for the setup and teardown phases. The distance between sender and receiver is 5,000 km apart. The propagation speed is given as 2 x 10 ms. Examine the total delay if 100,000 bits of data are involved during the data transfer phase?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

The following data are transmitted in a serial communication system (P is the parity bit). What parity is being used in each case? a. ABCDEFGHP = 010000101 b. ABCDEFGHP = 011000101 c. ABCDP = 01101 d. ABCDEP = 101011 e. ABCDEP = 111011
Given that the base address is FoH. 1. Create a new asm project “Lab2_Q1.asm". Assume that port A of 8255A PPI is connected to 8085. Write assembly code to send the value of FFH to FoH. Enter a delay of 2 ms for each transmission.
Consider the data sequence 10000011000010 Encode the sequence using HDB3. A digital link uses a channel that can convey frequency from dc to B Hz. Suppose the line coding NRZ Polar is used to send a maximum data rate of 100 Mbits/s using raised cosine pulse with roll-factor a = 0.6. (i) What is the symbol rate of the code? (ii) What is the minimum value of B?
3. Determine the implementation complexity of Time - Space (TS) switch where the number of Time Division Multiplexing input lines N = 65. Assume each input line contains a single DS1 signal (24 channels) and one stage matrix is used for space stage.
QUESTION 19 If the sequence "101010.. " is transmitted using Differential Manchester encoding, what is the ratio of the baud rate (D) to the bit rate (R)?
Exercise (3): A modem transmits using an 4-level signaling technique. If each signaling element has duration of 0.5ms. (a) Show the timing-diagram for a data stream 10111000111100010011 (b) Find the baud Rate and the bit Rate (c) How could you duplicate the transmission speed? Show the timing-diagram for a given data stream in (a). (d) How many bits per level are required if a modem using 7-level signalling mode? Exercise (4): A device is sending out data at the rate of 1000 bps. a. How long does it takes to send out 10 bits? b. How long does it take to sent out a single character (8bits)? c. How long does it take to send a file of 100,000 characters?
Write an ALP to transfer the message “CORONA” serially at 2400 baud rate, 8-bit data, 1- stop bit. Do it continuously.
27.Transmission protocol serial asynchronous 8 bits ASCII, 1 parity bit, 9600 bps. How long will it take for a kilobyte file to be transmitted through the link?
b. The output from the quantization process will be coded to generate bit stream to be encoded further using line encoding method. i. Determine two criteria in choosing the line encoding method. ii. Draw the encoded signal for a stream of 1000111 using bipolar Return to Zero-Alternate Mark Inversion (RZ- AMI).
A technique used to make the highest input data rate the dominant data rate and then add dummy bits to the input lines with lower rates. a. Frame synchronizing b. Multilevel-Multiplexingc. Multiple-slot allocationd. Bit stuffing
1.how does an additional 2 bits affect the SQNR ?
State a bit rate and maximum number of channels in T-1 and T-3 telephone TDM system.