A packet of resistors bought in an electronics component shop gives the nominal resistance value as 7000 N, and the manufacturing tolerance as +5%. If one resistor is chosen at random from the packet, calculate: The Minimum resistance values that this particular resistor is likely to have. The Maximum resistance values that this particular resistor is likely to have.

A packet of resistors bought in an electronics component shop gives the nominal resistance value as 7000 N, and the manufacturing tolerance as +5%. If one resistor is chosen at random from the packet, calculate: The Minimum resistance values that this particular resistor is likely to have. The Maximum resistance values that this particular resistor is likely to have.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

A PMMC instrument has internal resistance of 0.51 kN and gives full scale deflection for 41 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 56 V will be, ohms. O a. 222.14 O b. 136.08 O c. 109762.92 O d. 855.85
Five lamps are connected in series. Each lamp requires 16V and 0.1 A. Find the total voltage. A material that offers low resistance to a current flow in one direction and a high resistance in the reverse direction. If I inject a current gain of 4A in a transistor and a base voltage of 3.7V, what type of material allows freely the passage of electricity through itself? Semiconductor, Resistor, Insulator or Conductor If I inject a current gain of 4A in a transistor and a base voltage of 3.7V, what type of material allows freely the passage of electricity through itself? Two lamps x and y are connected in series. Lamp x is rated 50 watts at 100V, while lamp y is rated at 100 Watts at 100V also. Tue two lamps are to be connected in series across a 200V source. What resistance must be connected at lamp A so that each lamp will operate properly? Which is not a source of DC EMF? Thermocouple, Inverter, Piezoelectric cell, or batteries What is the maximum voltage that can be safely applied…
The zener diode dissipates most power when the output current is zero, that is when no load is connected to the power supply. In order to prove the veracity or otherwise of this statement by designing a simple power supply with an input voltage of 13 V, and capable of delivering up to 1 A, with an output voltage of 10V. You are to sketch the circuit and calculate the value of the limiting resistor, power rating of the limiting resistor, the power rating of the 10V zener diode used in the circuit on no load condition, the power rating of the Zener diode with a load resistance of 2kΩ. Assume a current of 10mA flows through the zener diode to keep it in zener breakdown.
For the ideal-diode clipper circuit given below, VS = 12.sinwt V. a. Determine the output voltage Vout and sketch this function. b. Remove the short circuit between points x and y, and replace it with a 2k2 Resistor. Find the range of values of VS for; D1 and D2 are OFF D1 is ON and D2 is OFF D1 is OFF and D2 is ON Is it possible for both D1 and D2 to be ON? y 1kO 3V D2 VS 3kQ. Vout D1 6V
Using the Mathematical and Graphical Method, Determine the Qpoint and terminal voltages for the given circuit below. Compare the values from the two different approaches. Determine the terminal voltages and currents and the inter-electrode voltages.
Create a table that showing the differences on using NI Multisim and actual evaluation of circuits.
A PMMC instrument has internal resistance of 0.66 kn and gives full scale deflection for 30 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 57 V will be ohms. O 86333.64 O 189.34 O 1240.00 O -133.68
Consider the two devices shaun below which are fabricated from the semiconductor material. same i) ii) p-type metal n-tmpe Metal metel n-pe metal than ncident on b) if the metal contects across the device is connected with a wire, do you expect current flow hE any ii). in device i) and Explain in te werds each.
4. From the figure shown which is series-parallel, the following values are: ID ohms in series with the parallel combination of 30 and DD ohms respectively. If the supply voltage is bD volts, find the following: a) equivalent resistance b)total current c)individual current d)current at 3D and D ohms only
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A noncontributory semiconductor has some holes in room temperature. What causes these holes?Please select one:a.Valuation electronsb.Dopingc.Free electronsd.Thermal energy
Compute for the following values and show compelete solutions. Find the following: A.) isc B.) iN C.) VN D. Draw circuit equivalent