A motot is aligned using pieces of steel under the base. The thicknesses of the pieces are as follows: 13/16 inch, 5/64 inch, 3/32 inch, 1/8 inch. What is the total thickn

Q: What are the disadvantage of steel sheeting?

A: The disadvantage of steel sheeting are as follows:

Q: When the length of the board is in inches, what is the formula used for B.F? _____

A: Board foot ( B.F.)  is the standard unit used for measurement of lumber

Q: We would like to increase the yield strength of the bar through cold work. (a) Using the Copper…

A:

Q: Explain zinc-tin alloy coated stainless steel.

A: Zinc(50%)-tin(50%) alloy coated stainless steel is known as Terne. This alloy had a low melting…

Q: 35. What grade of steel is most commonly used today in the production of W-shapes, and what are its…

A:

Q: What is a lightweight metal?

A: Light weight metal is any metal is relatively low density Li become increasingly critical in the…

Q: Describe about the spun-bonded process?

A: Spun-bonding:

Q: #5.) GIVEN: FIND: Ix of the composite shape 12x30

A: To Determine Moment of Inertia of the composite shape about Centroidal x-axis.

Q: 2. Discuss how structural steel is tested in the aboratoryforquality contro. Cite relevant ASTM…

A: Different tests, including destructive as well as nondestructive, are carried out to describe the…

Q: Differentiate quartz and quartzite

A:

Q: A column splice is used to increase

A: Column splicing is done to achieved the desired length on site . Column splicing is made because…

Q: What can be added to overcome surface tension and make a thin square steel sink in water?

A: Cohesion between water molecules which pull the water molecules of surface downiseide creating a…

Q: What is yield strength of reinforcing steel (yield strength 40,000 psi) at a temperature of 430°C…

A: Given  Yield strength= 40,000 psi  Temperature= 430 °C

Q: How can flaws in steel and welds be detected? Discuss the concept of a nondestructive test used for…

A: During production of steel and during process of welding, many factors may cause defect on…

Q: What is the Minimum diameter of steel in Column ?

A: The minimum diameter of the steel reinforcement in the Column is specified in the Standard code…

Q: Compare between slip casting and tape casting

A:

Q: A steel plate is 300 mm wide and 10 mm thick. A rivet of nominal diameter of 16 mm is driven into…

A: Diameter of the hole =do+1.5    (do≤25mm)d=16+1.5=17.5mm

Q: Why is malleable cast iron less brittle than white cast iron?

A: Brief concept- Brittle material- Those materials which break on the application of the stress…

Q: Determine if w12x14 (A36) section is Compact, Non-Compact or slender. Show neat handwriting and…

A: The given data is shown below: W12×14A36 steel

Q: Based from color, what is the major indicator wether a reinforcing steel bar is weldable or not?

A: There are a few ways to tell the difference between grades of steel rebar. One of the easiest is to…

Q: What are the commonly produced cast irons?

A: Cast Iron Cast Iron is an alloy of iron that is composed of 2% to 4% of carbon content and different…

Q: Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @…

A:

Q: Immerse samples of interior and exterior plywood in water. Continue until delamination occurs. Keep…

A: Interior Plywood: Interior plywood is used as a material for indoor works. Interior plywood should…

Q: Discuss Selection and Sizing of Anchor Bolts

A: Solution: When anchoring, the general rule is that the embedded depth  should be at least 4 diameter…

Q: methods to protect steel tension members from rust and corrosion.

A: These members are subjected to axial tensile forces.These forces try to elongate the members.

Q: what is the Weight of the wood if the cross-section is 200 mm x 200 mm?

A: Data Given: A = 200 mm × 200 mmWood projection when placed in water = 55 mmWood projection when…

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

A:

Q: The minimum thickness of a square base plate with A1= B x N=A2= 600 in2 subjected to Pu = 500 k and…

A:

Q: Three main STEEL making processes. Briefly describe each process.

A: The three major steelmaking processes are: Basic oxygen Open hearth and Electric arc

Q: With examples, describe what marble is and what it is most commonly used for.

A: When limestone is exposed to intense pressure or heat, marble is created. Marble, which is made of…

Q: mechanical properties changes during tensile test

A: Mechanical properties- These are those properties which changes due to change in temperature,…

Q: The part of the shown graph shows no permanent deformation. Select one: a. Black b. Red C. Green d.…

A: The given graph is stress-strain curve of mild steel.

Q: Which of the following options are correct for the section shown in figure? 40 mm 100 mm 100 mm…

A: Given data, To find the  (a)elastic section modulus (b)Shape factor

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

A:

Q: (2) 28"/ 2#8 14" I2.5" NwC fé=3000 psi > 2 #10 z 2 #11 I 3" Grade 60 steel &M=?

A: h = 28 in b = 14 in d' = 2.5 in fc = 3 ksi fy = 60 ksi tension bars, 2#10, 2#11 compression bars,…

Q: Find the moment of inertia (Ix, mm“) of the composite shape from the bottom base. Type answer in two…

A:

Q: Two 20 mm thick slabs are joined by a 10 mm thick slab as shown in the figure. The bolts used as…

A: The thickness of thinner plate=10 mm The thickness of the longer plate=20 mm Diameter=5/8 inch

Q: Process of fixing a frame in a door opening

A: There are mainly three types of door frames are available. 1. Wooden door frame2. Aluminum door…

Q: #5,) GIVEN: FIND: Ix of the composite shape C12x3 12x30

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.