A mercury barometer at the base of the mountain reads 515 mm. At the same time, another barometer at the top of a mountain reads 410 mm. assuming w of air is to be constant at 9 N/m3, what is the appropriate height of the mountain? Note: Specific gravity of mercury =13.6 and the unit weight of water is 9810 N/m3 A. 1665.52m B. 1654.52m C. 1556.52m D. 1655.52m

A mercury barometer at the base of the mountain reads 515 mm. At the same time, another barometer at the top of a mountain reads 410 mm. assuming w of air is to be constant at 9 N/m3, what is the appropriate height of the mountain? Note: Specific gravity of mercury =13.6 and the unit weight of water is 9810 N/m3 A. 1665.52m B. 1654.52m C. 1556.52m D. 1655.52m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A=50kn B=28kn/m C=20kn/m
2. 0.1 m at a constant temperature and pressure seen in the figuren water flowing through a diameter pipe with a mass flux of 6000 kg/m's, then a 0.3 m diameterpipe with orifice attached to it it is transitioning to the line. The orifice-bound and manometer sIVisi ilcm between arms in the manometer containing mercury the difference has been observed to be. As a result of the measurements made the origins of permanent pressure loss, pressure loss It was found to be up to 81%. Accordingly; a) permanent pressure in the pipe due to orifice calculate the loss in terms of pascals (APK receiver). B) calculate the linear velocity value in the orifice (V)). orifis Drection of fow D, = 0.1 m D, = 0.3 m G. = 6000 kg / m2s h=1 cm Data: • Pau = 1000 kg / m2, = 13600 kg / m3 %3D
Determine the moments of inertia Ix and Iy of the surface below, with respect to the barycentric axes, respectively, parallel and perpendicular to side AB. 25 mm 25 mm 25 mm A 250 mm uu 001
3.23 A tank is fitted with a manometer on the side, as shown. The liquid in the bottom of the tank and in the manometer has a specific gravity (SG) of 3.0. The depth of this bottom liquid is 20 cm. A 15 cm layer of water lies on top of the bottom liquid. Find the position of the liquid surface in the manometer. 15 cm Water Ah =? 20 cm SG = 3.0 Problem 3.23
9. A simple manometer is used to measure the pressure of oil (sp. gr. = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left limb is connected to the pipe. The centre of the pipe is 9 cm below the level of mercury (sp. gr. 13.6) in the right limb. If the difference of mercury level in the two limbs is 15 [Ans. 12.058 Niem'] 10. A simple manometer (U-tube) containing mercury is connected to a pipe in which an oil of sp. gr. 0.8 is flowing. The pressure in the pipe is vačuum. The other end of the manometer is open to the atmosphere. Find the vacuum, pressure in pipe, if the difference of mercury level in the two limbs is 20 cm and height [Ans. - 27.86 Nicm] 11. A single column vertical manometer (i.e., micrometer) is connected to a pipe containing oil of sp. gr. 0.9. The area of the reservoir is 80 times the area of the manometer tube. The reservoir contains mercury of sp. gr. 13.6. The level of mercury in the reservoir is at a height of 30 cm below the centre…
A robot arm moves so that P travels in a circle about point B, which is not moving. Knowing that P starts from rest, and its speed increases at a constant rate of 10 mm/s, determine (a) the magnitude of the acceleration when t = 4 s, (b) the time for the magnitude of the acceleration to be 80 mm/s?. %3D 0.8 m В Answer: a. 10.20mm/s? -- --
Calculate Pa-Pb in the manometer below
Determine the moment of inertia of the shaded area with respect to y-axis Where: b1=10mm b1 b2 b2 b1 b2=45mm h=40mm h1 h2 = 21mm h2 h2 h2 h2 b1 - b1
A jet having a diameter of 38 mm and a velocity of 18 m/sec strikes a series of vanes so arranged on the periphery of a wheel that the entire jet strikes the vanes. The deflection angle of the vanes is 170 degrees. (a) Determine the maximum amount of work that can be done. (b) Determine the direction and absolute velocity of water leaving the vanes.
Sample problem 2: (256) Oil flows from a tank through 150 m of 150mm diameter pipe and then discharges into air. If the head loss from point I to point 2 is 600 mm, determine the pressure needed at point I to cause 17 lit/sec of oil to flow. El. 30 m Air, p-? El. 20 m Oil S 0.84 ఆదిరిదిి 150 m - 150 mm O
Mechanics of Materials Lab MECH 305, Tutorial-1: Review 100 mm 3. Moment of inertia on an area Determine the moments of inertia of the beam's cross-sectional area shown in Fig. about the x and y centroidal axes. 400 mm 100 mm 600 mm- 400 mm -100 mm
6. A clean tube of internal diameter 3 mm is immersed in a liquid with a coefficient of surface tension 0.48 N/m. The angle of contact of the liquid with the glass can be assumed to be 130° The density of the liquid is 13,600 kg/m^3? What would be the level of the liquid in the tube (in mm) relative to the free surface of the liquid outside the tube. (2 decimal places)