A magnetic core with an air gap is shown below. For a relative permeability is 3500, and the space free permeability is 4πx107 H/m. Find the reluctance of the left leg and the top side of the core. Ignore the gap in your calculations. 10 cm N 0.1 cm gap 20 cm 5 cm 5 cm 40 cm core depth = 10 cm 5 cm Select one: O a. Rleft = 1251 A.t./Wb, Rtop 1023 A.t/Wb O b. None C. Rleft 12.51 KA.t./Wb, Rtop = 10.23 KA.t/Wb = d. Rieft 125.1 A.t./Wb, Rtop = 102.3 A.t/Wb Clear my choice <

A magnetic core with an air gap is shown below. For a relative permeability is 3500, and the space free permeability is 4πx107 H/m. Find the reluctance of the left leg and the top side of the core. Ignore the gap in your calculations. 10 cm N 0.1 cm gap 20 cm 5 cm 5 cm 40 cm core depth = 10 cm 5 cm Select one: O a. Rleft = 1251 A.t./Wb, Rtop 1023 A.t/Wb O b. None C. Rleft 12.51 KA.t./Wb, Rtop = 10.23 KA.t/Wb = d. Rieft 125.1 A.t./Wb, Rtop = 102.3 A.t/Wb Clear my choice <

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The _________ model has the advantage that the parameters are defined by the actual operating conditions. a.re b.hybrid-pi c.pi d.hybrid
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The minimum feeder-circuit conductor size, before the application of any adjust mentor correction factors, shall have an allowable ampacity not less than the non-continuous load plus the continuous load. 156 % 110% 100% 125%
don't use third party content 1716. Explain the concept of hierarchical attention in funnel transformers.
Complete using the 2020 NEC, Table 310.16, 310.15(B)(1), and 310.15(C)(1) or 2023 NEC, Table 310.16, 310.15(B)(1)(1), and 310.15(C)(1)
GIVEN: Three-phase System Data: 30 Source ZLine 30 Load Ean Zan = Zbn = Zen = 0.1 + j1.5 n Source: 12020° v; Epn = 1202 – 120° v; Een = 1204120° v (grounded neutral) Line Impedance: Zline a = Zline b Zline c = 1+ j2 N; C Load Impedance: Zab 40 + j30 N; Zbc = 40 – j30 N; Zca = 50 + j0 N %3D %3D
The final circuit of the 6-streets traffic light controller:
1. A MRT (Metro Rail Transit) car, 5km distance from Taft Station takes 100A over hard drawn copper trolley wire having a resistance of 0.270 per km. The rail and ground return wire have a resistance of 0.060 per km. (a) If the station supply voltage is 550V, what is the receiving end voltage at the car side? (b) If a line to ground fault occurs at the supply voltage causing a very high current of 500A, what is the new receiving end voltage at the car side?
Please answer question 7 ONLY.
Solve 34 plz fasttt...hand written plz i'll give you multiple upvote
Check the correct statements. *
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The per-unit values of positive, negative, and zero sequence reactances of a network at fault are 0.08, 0.07, and 0.05 respectively. Determine the per-unit fault current if the fault is line-to-line-to-ground. j10 j12 j14 j16
Please click on pic to open it