formula for admittance and draw the current triangle and admittance triangle for parallel RL circuit.(Si

Q: Briefly explain why E = 0 inside a conductor? ‘A conductor is an equipotential’ give your opinion on…

A: Solution: (1) when an electric field is applied to a conductor, The negative charge (free electrons)…

Q: 7) Two conductors of the same length and material but of different cross-sectional area are…

A: Assume that  Length of conductor 1 =L Cross section area of conductor A =A1 Length of conductor 2=L…

Q: Define and draw unit circle. What is the significance of unit circle for system analysis?

A: to draw and define unit circle significance of unit circle for system analysis

Q: What does a negative value of loop current indicates in Mesh Analysis and Method of Branch Currents,…

A: Mesh Analysis: It is a method of solving electrical circuits.

Q: In single phase power factor meter there is error due to frequency and waveforms but not in three…

A: It is given that:Why there is an error due to frequency and waveforms in the single-phase power…

Q: AMoving to another question will save this response. uestion 8 Which of the following is the phase…

A: In this question we need to choose a correct option.

Q: can you please further explain the peak power delivered to r2 portion. thank you

A:

Q: Match the following questions with correct answer. Use of double circuit lines: Choose.. In case of…

A: In this question we will write about double circuit line uses..

Q: have an underground buried cable, suppose the cable is derected (oper circuit) somewhere along its…

A: Given that an underground buried cable has open circuit fault and we have to locate the position of…

Q: differentiate between overhead service connection and under ground service connection with sketch

A: Overhead Service Connection:- Electric locomotives, trolleybuses, and trams receive their electrical…

Q: The faults which give rise to unsymmetrical currents (unequal line currents with unequal…

A: The above statement is incorrect or false.

Q: What is the different b/w solid type cables and pressure cables (oil and gas)...

A: There are various ways of classifying the cables and the classification depends upon various…

Q: Explain in detail what is a nodal line. Provide an example and diagram for it.

A: In order to understand Nodal line we first have to understand some basic terms such as Wave…

Q: What is granding of cables? Explain.

A: to explain grading of cables

Q: the slip-rings replaced by separated segments In order to generate a bidirectional Voltage true /…

A: This statement is true or false?  "the slip-rings replaced by separated segments In order to…

Q: 5. A two wire DC distributor 0.8 kilometre long is supplying two loads 10A and 20A at 500 meter and…

A: As per Bartleby guidelines we are allowed to solve only three subparts,please ask the rest again.…

Q: 9. The generator power is always the maximum load power. c. equal b. less than d. greater than or…

A:

Q: What is the relation between the voltage drop and the distance in radial and ring circuit?

A: Concept: Using a constant voltage system, electrical power distribution is performed. Radial…

Q: A 1000 m long distributor "AB" supplying DC 500V from point A, with a pair of conductors to the…

A:

Q: What are the different types of power generation sources, and how do they impact the grid

A: we need to explain:the primary sources of energy generation in a power system and how they impact…

Q: In residential and commercial buildings, what kind of circuit connection is being used? Is it series…

A: Type of connection which is used in residential and commercial buildings :  Parallel connection…

Q: Crosstalk Glitch Example and Analysis Aggressor Victim Victim Net, V OM Aggressor Net, A Coupling…

A:

Q: Q-5-) 60 Hz generator supplies 0.50 Pmax power to a busbar with infinite power over a conveying…

A: To calculate the critical clearance angle of the system using the transient area criterion method,…

Q: Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material…

A: electrical gradient in a cable is given by  g=potentail differnecex lnR2R1   = Vx lnR2R1

Q: 5A x)2 A The figure shows four closed paths around three current-carrying wires. Rank the paths in…

A: Given figure,

Q: Question 4 In case of N-R method of power flow solution at the generator bus one column and one row…

A: 4) Newton- Raphson method of power flow solution at the generator bus

Q: What is the number of overall systems?

A: SOLUTION If we talk in reference of ELECTRICAL CONTROL SYSTEM there…

Q: Q In a two-bus organization, * Two buses may be used as source buses while the end is used as…

A:

Q: Does RTD have a treshold and a dead space? If yes, explain them.

A: Given: Does RTD have a treshold and a dead space? If yes, explain them

Q: 4) Reduce the block diagram of the system using Mason's Rule. Rist Dy Xx(x) -26 -24

A:

Q: (b) Determine the inductance per km/phase of a double circuit three-phase line as shown in the given…

A:

Q: What is the super tension cable and application,rating

A: In this question we are discussing about super tension cable and application,rating. This is…

Q: why capacitance voltages dividers are not preferred for high d.c. voltage measurments ??

A: Capacitor: The term "capacitor" refers to a device without a unit. The ratio of the charge held in…

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.