A machinist wishes to insert a silver rod with a diameter of 8 mm into a hole with a diameter of 7.991 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?

A machinist wishes to insert a silver rod with a diameter of 8 mm into a hole with a diameter of 7.991 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter16: Temperature And The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 8P

See similar textbooks

Related questions

Q: Figure CQ11.11 shows a composite bar made of three different materials that connects a hot reservoir…

A: The heat flow will be same as the bar is continuous.From heat flow,

Q: For each of the following temperatures, find the equivalent temperature on the indicated scale: (a)…

A: (a). -273.15°C on the Fahrenheit scale is

Q: In a cooler bag with an area of 1.0 m^2 and a wall thickness of 2.0 cm is 0.5 kg ice. For how long…

A: Given data: The area of bag is A=1 m2. Wall thickness is l=2 cm. Mass of ice is m=0.5 kg. Inside…

Q: A machinist wishes to insert a brass rod with a diameter of 4 mm into a hole with a diameter of…

Q: When the temperature of a copper coin is raised by 120 C°, its diameter increases by 0.20%. To two…

Q: A machinist wishes to insert a steel rod with a diameter of 4 mm into a hole with a diameter of…

Q: In an experiment to determine the thermal conductivity of a bar of new alloy, one end of the bar is…

A: When the two ends of a solid bar of cross-sectional area A and length Lare maintained at…

Q: A window of a car is found to be covered with 0.9 cm of ice. If the area of the window is 1 m2, and…

Q: 29 hot air balloons have a mass with a payload (without the air inside) of 200 kg, the temperature…

Q: A steel sphere of diameter 4.0025 cm is to be passed through a brass loop of inner. diameter 4.0012…

Q: An aluminum rod 177.4 cm long at 20 °C is heated to 100 °C. What is the new length? Aluminum has a…

Q: A machinist wishes to insert a steel rod with a diameter of 5 mn into a hole with a diameter of…

A: Given info: Initial diameter = 5 mm Diameter to be achieved by changing temperature = 4.997 mm So,…

Q: A cylinder of diameter 3.00000 cm at 250 C is to be slid into a hole of a steel plate. The hole has…

A: According to the definition of linear expansion

Q: A machinist wishes to insert an iron rod with a diameter of 4 mm into a hole with a diameter of…

A: The expansion in area due to the increase in temperature is given by where, A is the initial area,…

Q: When the temperature of a copper coin is raised by 100 C°, its diameter increases by 0.17%. To two…

A: Given value--- after increasing 100 degree C temperature, the diameter of coin increases by 0.17 %…

Q: At a temperature of 22.20°C the hole in a steel plate has a diameter of 1.030 cm. If a steel rod…

Q: A glass container has a total wall area (including the lid) of 1.75 m2 and a wall thickness of 1.5…

Q: A cooking pan whose inner diameter is 20 cm is filled with water and covered with a 4-kg lid. If the…

A: Given: Diameter, d = 20 cm Thus, radius r = d/2 = 20/2 = 10 cm = 0.1 m. Mass m = 4 kg Atmospheric…

Q: A brass plug has diameter 10.0 cm @ 25°C. To what temperature must the plug be chilled with dry ice…

Q: A glass rectangular prism has the surface area of 0.120 m^2. The coefficient of linear expansion for…

A: The change in surface area is given by, ΔA=αAAΔT Here, αA is the coefficient of area expansion, A is…

Q: A copper rod is 0.863 m long with a rectangular cross section of dimensions 0.0519 m by 0.0867 m.…

A: length of copper rod = 0.863 m cross section of rod = 0.0519 m by 0.0867 mTemperature at the ends of…

Q: A 5-meter long Brass rod with a diameter of 0.01meter increases in length by 0.05 m when its…

Q: In an experiment to determine the thermal conductivity of a bar of a new alloy, one end of the bar…

A: Given, One end of the bar is maintained at 0.0 °C and the other end at 100.0 °C , so ∆T = 100°C. The…

Q: 500 g of Ice at 0 °C is kept in an insulated cubic box. The length of the box is 30 cm and the…

Q: 18. A 33 cm long Cu rod's one end is exposed to 500 Celsius and the other end at 20 Celsius.…

A: The rate of heat flow along the copper rod is calculated by using the given equation below. Here, k…

Q: An aluminum coffee mug has in inner diameter of 2.50 cm at room temperature (20.0° C). If someone…

Q: In an experiment to determine the thermal conductivity of a bar of a new metal alloy, one end of the…

Q: Question 16 A granite wall has a thickness of 78 cm, an area of 7.33 m by 2.85 m and a thermal…

A: Given:Thickness of granite wall, L = 78 cmArea of granite wall, A = 7.33×2.85 = 20.8905 m2Thermal…

Q: An aluminum rod 177.4 cm long at 20 °C is heated to 100 °C. What is the new length? Aluminum has a…

A: Given --- length of the aluminum rod = 177.4 cm. initial temperature = 20 degree C. final…

Q: A Styrofoam box has a surface area of 0.88 m2 and a wall thickness of 2.0 cm. The temperature of the…

A: The latent heat of fusion for ice is (Lf) = 3.33*105 J/kg The thick ness of the wall (l) = 2*10-2 m…

Q: A machinist wishes to insert a copper rod with a diameter of 7 mm into a hole with a diameter of…

A: Given L=2\,\text{mm}=2\cdot {{10}^{-3}}\text{m}L= 7[mm]= 7×10-3[m] \Delta…

Q: At a temperature of 22.90°C the hole in a steel plate has a diameter of 1.025 cm. If a steel rod…

A: The initial temperature of the steel plate is. The coefficient of area expansion of the steel plate…

Q: A machinist wishes to insert a copper rod with a diameter of 4 mm into a hole with a diameter of…

A: Given : d=4 mm d'=3.995 mm We have to find the temperature which is to be lowered to make sure that…

Q: A surveyor uses a steel measuring tape that is exactly 75000 m long at a temperature of 20 degrees…

Q: · A 3.2 m length of copper pipe extends directly from a hot-water heater in a basement to a faucet…

A: Given data: Original Length (L0) = 3.2 m Initial temperature (Ti) = 20.0°C Final temperature (Tf) =…

Q: A surveyor uses a steel measuring tape that is exactly 75000m long at a temperature of 20 degree…

A: Write the given values with the suitable variables. L=75000 mT1=20 °CT2=35 °Cα=1.2×10-5 /K Here, L,…

Q: A plane wall is 2 meter high by 3 meter wide and is 2 cm thick. It is made of 0.50 W/m-K. A…

A: There are numerous applications for the heat flux value. It aids in the evaluation of heat transfer…

Q: A machinist wishes to insert a brass rod with a diameter of 4 mm into a hole with a diameter of…

Q: A window has dimensions of 1.55 m by 2.65 m and is made of glass 5.5 mm thick. On a winter day, the…

A: Given The dimensions of the window 1.55 m x 2.65 m Thickness of glass 5.5 mm = 5.5 x 10-3 m Outside…

Q: A 900 cm X 1080 cm house is built on a 17 cm thick concrete slab of thermal conductivity 0.74…

A: GivenDimension of house =900 cm×1080 cmThickness of concrete slab, ∆x=17.6 cmThermal conductivity,…

Q: A glass container has a total wall area (including the lid) of 1.75 m and a wall thickness of 1.5…

Q: A pond with a flat bottom has a surface area of 946 m2 and a depth of 2.44 m. On a warm day, the…

A: The rate of heat energy due to conduction is

Q: The coefficient of thermal conductivity of copper is seven time that of Aluminium. In the composite…

A: solution: given that coeffiecient of thermal conductivity of copper is seven times that of aluminium…

Q: Find the thickness of the wall in meter if the temperature of the inside room is 68.5 o F and the…

Q: A machinist wishes to insert an iron rod with a diameter of 9 mm into a hole with a diameter of…

A: Given that, Diameter of iron rod(d1)= 9 mm= 9× 10-³ m Diameter of hole(d2)= 8.998 mm= 8.998× 10-³ m…

Q: If I have an unknown substance of mass m=2.54kg which requires Q= 3430J of heat to change its…

A: mass of unknown substance (m) = 2.54 kg Heat (H) = 3430 J Change in temperature = 10 kelvin

Q: 1100 m³. The density of air at 20 °C is 1.205 kg/m³. The density of hot air inside the balloon at a…

A: A hot air balloon has a volume of 1100m3 The density of the air outside the balloon is 1.205 kg/m3…

Q: At a temperature of 22.00°C the hole in a steel plate has a diameter of 1.040 cm. If a steel rod…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given and required quantities

VIEW

Change in diameter of the rod

VIEW

Change in temperature

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A machinist wishes to insert a copper rod with a diameter of 7 mm into a hole with a diameter of 6.992 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
please answer the following: A) An aluminum wing on a passenger jet is 36 m long when its temperature is 16°C.At what temperature would the wing be 2 cm (0.02 m) shorter? B) A machinist wishes to insert a brass rod with a diameter of 9 mm into a hole with a diameter of 8.998 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
A hole is drilled in a copper sheet. The diameter of the hole is 4.24 cm at 27.0 °C. What is the change in the diameter of the hole when the sheet is heated to 227 °C? Coefficient of linear expansion of copper =1.70×10-5 K-1.
A copper plate has a hole with a diameter of 2.50 cm. A copper shaft with a diameter of 2.501 cm is to be inserted into the hole. If the linear coefficient of thermal expansion for copper is 17.0 × 10−6/°C, then what decrease in temperature of the copper shaft is required for the shaft to just fit inside the hole
A company advertises that it delivers helium at a gauge pressure of 1.72 × 10 7 Pa in a cylinder of volume 43.8 L. How many balloons can be inflated to a volume of 4.00 L with that amount of helium? Assume the pressure inside the balloons is 1.01 × 105 Pa and the temperature in the cylinder and the balloons is 25.0 °C .
An aluminum can is filled to the brim with a liquid. The can and the liquid are heated so their temperatures change by the same amount. The can’s initial volume at 8 °C is 6.5 × 10-4 m3. The coefficient of volume expansion for aluminum is 69 × 10-6 (C°)-1. When the can and the liquid are heated to 80 °C, 4.9 × 10-6 m3 of liquid spills over. What is the coefficient of volume expansion of the liquid?
A circular hole in an aluminum plate is 2.386 cm in diameter at 0.000°C. What is its diameter when the temperature of the plate is raised to 75.50°C? The linear expansion coefficient of aluminum is 23.00 x 10-6 /C°. Number Units Use correct number of significant digits; the tolerance is +/-2%
A machinist wishes to insert an iron rod with a diameter of 4 mm into a hole with a diameter of 3.996 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
You drop an ice cube into an insulated flask full of water and wait for the ice cube to completely melt. The ice cube initially has a mass of 90.0 g and a temperature of 0°C. The water (before the ice cube is added) has a mass of 850 g and an initial temperature of 22.0°C. What is the final temperature (in °C) of the mixture? (Assume no energy is lost to the walls of the flask, or to the environment.) °C
A machinist wishes to insert a brass rod with a diameter of 4 mm into a hole with a diameter of 3.995 mm. By how much would the machinist have to lower the temperature (in °C) of the rod to make it fit the hole?
A copper plate has a length of 0.12 m and a width of 0.10 m at 25 °C. The plate is uniformly heated to 175 °C. If the linear expansion coefficient for copper is 1.7 × 10–5/C°, what is the change in the area of the plate as a result of the increase in temperature?
You drop an ice cube into an insulated flask full of water and wait for the ice cube to completely melt. The ice cube initially has a mass of 65.0 g and a temperature of 0°C. The water (before the ice cube is added) has a mass of 670 g and an initial temperature of 28.0°C. What is the final temperature (in °C) of the mixture? (Assume no energy is lost to the walls of the flask, or to the environment.)