A load F of 500 N is applied in the negative x-direction on rod OA, and a load P of 200 N is applies in the negative z-direction at point B on rod AB. Assume rod AB is fixed to rod OA and rod OA is fixed along the left side to a wall. Point C is along the frontmost edge of rod OA, in the XZ plane. 0.5 m 0.1 m C F What, if any, are the bending moments and torques at point C? Choose all that apply.

A load F of 500 N is applied in the negative x-direction on rod OA, and a load P of 200 N is applies in the negative z-direction at point B on rod AB. Assume rod AB is fixed to rod OA and rod OA is fixed along the left side to a wall. Point C is along the frontmost edge of rod OA, in the XZ plane. 0.5 m 0.1 m C F What, if any, are the bending moments and torques at point C? Choose all that apply.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.8P: A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure)...

See similar textbooks

Similar questions

A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Pivot pont y r=8 315 165. Load X45 Cell 1 -X A frame is being raised on a pivot point. pointo a crane lifts the frame and shows. 315 165 at 45⁰. How much force is needed to raise the frame
1. A tripod shawn supports of note that ball and rocket joints are used to mount the tripuod a load P=1000N at point A. Take at points B,D, and C. consider the t LI L 2 L2: 4 L3 : 3 A : 45° g :30° %3D on x-z plane L2 POINT C (2,-2,3) C0,0,0) ミー- Determine the ff Force of AB - N Force of AC - N Force of AD : N
A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 = 115 k, P3= 55 k, P4 = (P1-P2+P3) k. If Section 2 has a length, L2 = 65 inches, find the change in length of Section 2. Report the answer below in inches, absolute value, 3 significant digits. P1 Your Answer: 100 inches Round Steel Bar P2 Section 2 12 P3 80 inches P4
Set P₁= 2 kN and P₂ = 1.5 kN. (Figure 1) Figure 30° -3m D 30° 3m 1 of 1 Copyright @ 3032 D.
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm ТАКE a-9,6 60.a mm 50 mm D Yatağı 100 mm C t mm |F=100 kN
100 mm 100 mm -300 mm 400 N 250 mm 400 N B D A 150 mm -500 mm- 4) If member ABC supports the shown loads and itached to a wire B0, the tension in wire B0 equs OA 1416 N MacBook Pro 1448 N 55 %24 W 2
Required information Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Given: P₁ = 65 kN and P2 = 40 kN. Take Es = 200 GPa and Eb = 105 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -180- Dimensions in mum Steel B 120- P₁ 40-mm diam. 100 100 DI C Brass 30-mm diam. Determine the reactions at A and E. The reaction at A is The reaction at Eis P2 E KN (Click to select) ✓ KN (Click to select)
Q1: Draw just the Free Body Diagram of the following figures. D Figure (1) Figure (2) Figure (3) T 30° 45° 60° - Figure (4) Figure (5) 26 kN 250 N 30 13 12 30 0.15 m 0.4 m B. 0 m 2 m 4 m
For the figure show find the value of A by using just (EFx) F=4 kN A 0=60° 0=60° A=4 kN A=6 kN A=5 kN None of them