A liquid of viscosity of 0.03 N s m 2 is flowing under laminar conditions through a convergent, tapered tube for which the tube diameter changes linearly with length. The tube length is 0.50 m and its diameter varies from 0.01 m at the entrance to 0.005 m at the exit. Determine the pressure drop which is required to maintain the flow at a rate of 10-7 m3 s-1. The effect of kinetic energy due to the change in velocity in the tube may be neglected. Show the derivation of the final eauation used in solving this problem.

A liquid of viscosity of 0.03 N s m 2 is flowing under laminar conditions through a convergent, tapered tube for which the tube diameter changes linearly with length. The tube length is 0.50 m and its diameter varies from 0.01 m at the entrance to 0.005 m at the exit. Determine the pressure drop which is required to maintain the flow at a rate of 10-7 m3 s-1. The effect of kinetic energy due to the change in velocity in the tube may be neglected. Show the derivation of the final eauation used in solving this problem.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water with a density of 999.1 kg/m3 and absolute viscosity of 1.138 X 103 kg/m-s is flowing steadily in a 30-m-long and 4-cm-diameter horizontal pipe made of stainless steel at a rate of 8 L/s. Find the pressure drop (KPa) within the span of the pipe. If the flow is laminar, use the figure below to calculate f. If the flow is turbulent, use 0.01573 as the value for f. Friction Factor Tube Geometry f Circle 64.00/Re
A viscous fluid flows in a cylindrical pipe with a diameter of 10 cm. The velocity of the fluid that is measured 0.012 m away from the pipe wall is 0.8 m/s. If the flow is laminar, determine the centerline velocity and the flow rate.
The oil whose temperature is constant at 20 ° C (ρ = 886 kg / m3, μ = 0.805 kg / m / s) flows continuously and fully developed from a length of 40 m of a pipe with a diameter of 5 cm. The pressure at the inlet of this 40 m length was measured as 720 kPa and the pressure at the outlet as 101 kPa. Flow is laminar. Volumetric flow rates, average velocities, Reynolds numbers and Darcy friction factorsa) The pipe is horizontalb) The pipe makes 20 ° counterclockwise with the horizontal.c) The pipe makes 15 ° clockwise with the horizontal.Calculate for situations.
Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance of 2000 m. Ifthe line is isothermal at 323.15 K and the pressure at the entry point is 750 ×103 Pa and at the exit point is 430×103 Pa, what diameter should the pipe has to ensure that the CO2 will be delivered to the end point with the pressure drop experienced. The viscosity of CO2 at 323.15 K is 1.45×10-5kg/m.s. One trial is sufficient given you tell us how you will proceed to achieve an accurate diameter estimate. Hint: for your initial guess, use D in the range of 0.01-0.02 m.
Determine the pressure drop, the head loss, and the pumping power required to overcome the frictional losses in the tube, if the liquid ammonia at -20°C is flowing through a 30- m-long section of a 5-mm-diameter copper tube at a rate of 0.15 kg/s. Ammonia D= 5 mm 0.15 kg/s L = 30 m
Determine the mean velocity of oil that has the specific gravity as 0.78 flowing in a pipe of cross-sectional area 11 x 10-5 m² and it takes 11 seconds for 26 liters in the storage tank. Mean Velocity of the oil (in m/s)
Oil is transported in a horizontal circular pipe with diameter 10 cm and volume flow rate of 0.003 m³/s. The oil density is p = 917 kg/ m³ and its dynamic viscosity is μ = 0.1 Ns/ m². Determine the Reynolds number and flow status (laminar or turbulent) in the pipe, and further calculate the head loss and pressure drop over 1000 m of this horizontal pipe. The flow is assumed to be fully developed laminar flow throughout the pipe.
Determine the mean velocity of oil that has the specific gravity as 0.83 flowing in a pipe of cross-sectional area 10 x 10-5 m2 and it takes 14 seconds for 26 liters in the storage tank. Mean Velocity of the oil (in m/s)
Question 2 How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbulent flow? Explain
Nitrogen having a temperature of T1T1 = 290 KK . and absolute pressure of p1p1 = 330 kPakPa flows into the smooth pipe at M1M1 = 0.3. It is heated at 100 kJ/[kg⋅m]kJ/[kg⋅m]. (Figure 1) Figure 1 of 1 Part A Determine the velocity of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. V2V2 = nothingnothing SubmitRequest Answer Part B Determine the pressure of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. p2p2 = nothingnothing
Liquid fuel of kinematic viscosity 2.37x10-6 flows through the pipe of diameter 15 cm. Determine the entrance length for the flow where the volumetric flow rate is 0.04 m³/s.
What are the primary considerations when selecting a flowmeter to measure the flow rate of a fluid?