A liquid of specifi gravity 1.75 flows in a 6cm horizontal pipe. The total energy at a certain point in the flow is 80Joules / Newton. The elevation of the pipe above a fixed datum is 2.6m. If the pressure at the specified point is 75kPa, determine the velocity of flow. A) 27.85 m/s B) 37.85 m/s 47.85 m/s 57.85 m/s D

A liquid of specifi gravity 1.75 flows in a 6cm horizontal pipe. The total energy at a certain point in the flow is 80Joules / Newton. The elevation of the pipe above a fixed datum is 2.6m. If the pressure at the specified point is 75kPa, determine the velocity of flow. A) 27.85 m/s B) 37.85 m/s 47.85 m/s 57.85 m/s D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8.14 A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity.
The flow is opened to the atmosphere at point D which is fed by a very wide reservoir that has a water surface elevation of (5+) meters as shown in the figure given below. Elevation of the horizontal axis BC is 1 meter. At sections AB the diameter of the pipe is (0.2+- meters and CD the diameter of the 100 pipe is (0.3+: meters. The flow is ideal (inviscid) and absolute atmosphere pressure is 9.81 N/cm?. Considering the pipe's diameter is (0.15+; m at section BC, find the discharges and the 100 а. velocities of the flow at other sections (AE, EB, BC, CF, FD). Draw the energy and hydraulic grade lines of the system. b. Assuming the system discharge is constant and has the value you have found in (a), calculate the minimum pipe diameter that the section BC can take and draw the energy and hydraulic grade lines of this situation. Note: Absolute vapor pressure of water is 2.26 kN/m?. 10 A E 2.5 D B m
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
Mato 5
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m