a) In the process of taking a rod reading, one can eliminate parallax mathematically. Parallax is basically a systematic error. True False b) The page check in the field notes is a quality control measure to determine if the user satisfied 1st order class I leveling. True False C) The upper cross hair reading was 8.00 ft. The lower cross hair reading was 6.00 ft. The stadia constant was 100. The horizontal distance from the center of the level to the face of the level rod = 200.0 ft. True False

a) In the process of taking a rod reading, one can eliminate parallax mathematically. Parallax is basically a systematic error. True False b) The page check in the field notes is a quality control measure to determine if the user satisfied 1st order class I leveling. True False C) The upper cross hair reading was 8.00 ft. The lower cross hair reading was 6.00 ft. The stadia constant was 100. The horizontal distance from the center of the level to the face of the level rod = 200.0 ft. True False

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How to solve for the Taped Distance and Percentage of Error? Show your step-by-step solution.
42. A 30-m steel tape is used to measure the distance of a line. The measured distance is 457.65 m. After the tape was calibrated, it was found that it is 16 mm too short. What is the correct length of the line? +8 8 A. 457.406 m C. 457.921 m D. 457.125 m B. 457.894 m
ANSWER ONLY LETTER D FOLLOW THE INSTRUCTIONS TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS
Find θA in radians using conjugate beam method.
2. During the measurement at the sides of the slope, the data was recorded into three bays, the following information (Table 1.0) was obtained: Table 1.0 Difference in Tension (N) Temperature (°C) Bay Measured Length (m) level between end (m) 1 25.842 19 +0.285 150 27.365 18 -0.236 120 3 21.645 21 -0.239 160 The 30 meter tape used has a mass of 0.400 N/m and a cross-sectional area of 3.00 mm?. It was standardised on the flat at 20 °C under a pull of 100 N, the actual length was 29.995 m during the measuring works. The coefficient of linear expension for the materials of the tape us 0.000015 / °C and Young's Modulus is 20.5 x 104 MN/m?. Calculate the absolute length of survey line in 3 decimal point. Slope correction = -v² 2s Sagging correction = - w²L³ 24P? Tension correction = (P – Ps) EL AE Temperature correction = a (T-Ts) (L)
Instructions: Show complete solution and box final answer/s.
9
A geometric (precise) leveling procedure is carried out between points A and B. When the height of point A is HA = 102.415 m, compute the height of point B. Rod readings are in mm. • Please write your answer in meters (e.g., 102.415) and with three decimal places after the decimal separator dot(.). • "Do not add m or meters at the end of your answer." 2867 2026 1475 0984 3102 2614 2452 1569
Given figure as shown. Tensions on cables BA and BC are also given. Take note of the positions of the coordinates, do not be misled, just follow their positions as shown. Твс-660 N %3D y 7 m 6 m 4.25 m -1 m 0.75 m Total distance BA is Total distance BC is The sign and numerical value of j component of the cable BA is The sign and numerical value of k component of cable BC is The sign and numerical value of i component of resultant vector R is Using point B and rB/0, the sign and numerical value of i component of Mo is