Which of the following would produce the greatest error when taping a distance of 100' with a steel tape? a. the tape is supported throughout but pulled with too litte tension b the tape is 2' off line c the tape is supported throughtout but pulled with too much tension d. the tape is on a 5% slope without correcting for it After a day of field work, you should copy and/or rewrite you field notes to make them nearer and more readable.

Which of the following would produce the greatest error when taping a distance of 100' with a steel tape? a. the tape is supported throughout but pulled with too litte tension b the tape is 2' off line c the tape is supported throughtout but pulled with too much tension d. the tape is on a 5% slope without correcting for it After a day of field work, you should copy and/or rewrite you field notes to make them nearer and more readable.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

e / My courses/ Civil Engineering / Engineering Surveying(Theory) / Mid Exam Engineering Surveying Ek to course 'Engineering Surveying(Theory)" n2 A line was measured to be 625.35 m using a 50-m steel tape under a pull of 6 kg. The mean temperature during the measurement is 22°C. The tape used has a cross-sectional area of 0.000003 m2 and has a standard length at 30°C under a pull of 8 kg. The modulus of elasticity of the tape is 2 x 106 kg/cm2 and the coefficient of thermal expansion is 1.16 x 10-5/°C. Calculate the corrected length of the ut of line. estion Paragraph 三三

Describe about the Dilatometer Method.
J A 非 Find end moment use slope- defliction 100kN C AK I 3m B 21 E 3m | 4m D
determine the relative error of the closure
Question: Calculate for Mmax of the beam
A 0.65kg, 50m tape was standardized and supported throughout its whole length and found to be 0.00205m longer at an observed temperature of 31.8°C and a pull of 10KN. This tape was used to measure a 4% prade line which was found to be 662.702m. During measurement, the temperature is 15°C and the tape is suspended under a pull of 20KN. E-200GPa, cross-sectional area of tape is 3mm2 and the coefficient of linear expansion is 0.0000116m/°C. Compute the true horizontal distance.
plz solve it within 30-40 mins I'll give you multiple upvote..hand write..thank you
attempt- 138326&cmid-4951 GGoogle O UVLe: Log in to the.. table 4. Which of the following shows an appropriate diagram of the tension forces acting on the ring such that it is possible for the resultant to be a zero vector? Note that the value of G is not equal to H. Hint: The eraser does not slide if the resultant of the frictional force and normal force is vertical. 5. Which of the following best approximates the value of the angle h (in degrees) if G = 100 N and H = 75 N? acer E11 NumLk Verr. Num F9 F10 F7 F8 F4 F5 F6 E3 8. 9) & 7 24 9. 6. U 4 5 0 6 P R H. 1 K 2 L G. MO CO
In Compass traversing length of lines are measured by O a. Dumpy level O b. Theodolite O c. Chain O d. Compass 2.
50 mm 100 mm 50 O 75 mm 100 100 50 h 75 e 9 75 a b ņ d For a failure through the staggered line abfcd, what is the gauge length (sg) of the stagger? + 75
4) Find the most economical wide flange section for an A992 steel beam (E = 29 x 10³ ksi) using LRFD which spans 45 ft. with a dead load of 50 lb/ft² and a live load of 95 lb/ft² if the beams are spaced 12 ft apart and full lateral bracing is provided. Determine the total maximum deflection. (Because the beam is fully braced, you should utilize a reference table with wide flanges in descending order of Z as found in the note set.) Additional wide flange properties which the text does not show text is provided on the following pages.
89 N has cross-sectional to an accuracy of ±- area of 6 mm² and a mass of 2.32 kg. It is to be used to measure lengths A steel tape 50 m long on the flat at 20°C under a pull of 1 10000 when supported at mid span. Assume that the ends of the tape and mid span support are the same level and the field temperature is 20°C. Determine the change in tension to be applied to ensure that an error greater than + 5 mm will not occur when measuring the length 50 m. Take Young's modulus to be 207 kN/mm² and g to be 9.81 m/s²